HP StorageWorks 2/32 SAN switch 2/32 version 4.0.x installation guide - Page 48

Power On, Self-Test, connector to create a Serial connection.

Get HP StorageWorks 2/32 - SAN Switch PDF manuals and user guides View all HP StorageWorks 2/32 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Installing the SAN Switch 2/32 Note: During first time setup, you must replace the factory IP, subnetmask and gateway addresses with addresses provided by your Network Administrator. 1. Remove the shipping plug from the SAN Switch 2/32 Serial port. 2. Connect the Serial cable to the SAN Switch 2/32 Serial port; see Figure 13. SHR-2572A Figure 13: Connecting the Serial cable 3. Connect the other end of the Serial cable to an RS-232 Serial port on the workstation. If no RS-232 Serial port is available on the workstation, the adapter on the end of the Serial cable can be removed to use the RJ-45 connector to create a Serial connection. 4. Verify that the switch power is on and POST is completed. See the "Power On Self-Test" section, earlier in this chapter. 5. Power on the workstation and establish a connection to the switch using a terminal emulator application (such as Hyperterminal). Note: These steps show instructions specific to Hyperterminal. If using a different application, consult the specific application's documentation. 48 SAN Switch 2/32 Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Installing the SAN Switch 2/32
48
SAN Switch 2/32 Installation Guide
Note:
During first time setup, you must replace the factory IP, subnetmask and gateway
addresses with addresses provided by your Network Administrator.
1.
Remove the shipping plug from the SAN Switch 2/32 Serial port.
2.
Connect the Serial cable to the SAN Switch 2/32 Serial port; see
Figure 13
.
Figure 13:
Connecting the Serial cable
3.
Connect the other end of the Serial cable to an RS-232 Serial port on the
workstation. If no RS-232 Serial port is available on the workstation, the
adapter on the end of the Serial cable can be removed to use the RJ-45
connector to create a Serial connection.
4.
Verify that the switch power is on and POST is completed. See the “
Power On
Self-Test
” section, earlier in this chapter.
5.
Power on the workstation and establish a connection to the switch using a
terminal emulator application (such as Hyperterminal).
Note:
These steps show instructions specific to Hyperterminal. If using a different
application, consult the specific application’s documentation.
SHR-2572A