HP StorageWorks 2/32 SAN switch 2/32 version 4.0.x installation guide - Page 72

Displaying Devices within the Fabric, Checking the Firmware Version, Fibre Channel Subnetmask

Get HP StorageWorks 2/32 - SAN Switch PDF manuals and user guides View all HP StorageWorks 2/32 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Managing the SAN Switch 2/32 6. At the Fibre Channel Subnetmask prompt, enter the address of the subnetmask, if applicable. Press Enter. 7. At the Gateway Address prompt, enter the IP address of the gateway system if applicable. Press Enter. The configuration is then committed to the switch firmware. 8. You are then prompted whether to make the IP address changes active now or at the next reboot. Enter y at the prompt to have the IP address changes take effect immediately. Displaying Devices within the Fabric To verify that you have fabric wide connectivity when you install a new switch, display the fabric wide device count from the newly installed switch. Use these steps to display the fabric. 1. Login to the switch as the admin user. 2. At the command line enter the following command: nsAllShow This command displays all the connected devices in the fabric. Checking the Firmware Version Use these steps to display the SAN Switch 2/32 firmware version. 1. Login to the switch as the admin user. 2. At the command line enter the following command: version This command displays the Kernel version, and Fabric OS release number. 72 SAN Switch 2/32 Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Managing the SAN Switch 2/32
72
SAN Switch 2/32 Installation Guide
6.
At the
Fibre Channel Subnetmask
prompt, enter the address of the
subnetmask, if applicable. Press
Enter
.
7.
At the
Gateway Address
prompt, enter the IP address of the gateway
system if applicable. Press
Enter
.
The configuration is then committed to the switch firmware.
8.
You are then prompted whether to make the IP address changes active now or
at the next reboot. Enter
y
at the prompt to have the IP address changes take
effect immediately.
Displaying Devices within the Fabric
To verify that you have fabric wide connectivity when you install a new switch,
display the fabric wide device count from the newly installed switch. Use these
steps to display the fabric.
1.
Login to the switch as the admin user.
2.
At the command line enter the following command:
nsAllShow
This command displays all the connected devices in the fabric.
Checking the Firmware Version
Use these steps to display the SAN Switch 2/32 firmware version.
1.
Login to the switch as the admin user.
2.
At the command line enter the following command:
version
This command displays the Kernel version, and Fabric OS release number.