HP StorageWorks 2/32 SAN switch 2/32 version 4.0.x installation guide - Page 40

Installing the Switch in the Optional HP System/e Rack

Get HP StorageWorks 2/32 - SAN Switch PDF manuals and user guides View all HP StorageWorks 2/32 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Installing the SAN Switch 2/32 Installing the Switch in the Optional HP System/e Rack This section provides instructions for installing the SAN Switch 2/32 in the optional HP System/e rack. The HP System/e Rack Kit consists of the following items: ■ HP System/e Rack Rail Kit - pre-merger HP part number A7340-87901; pre-merger Compaq part number QA-71AAA-GZ ■ HP System/e Rack Rail Kit Hardware - part number A7340-87902 The following hardware is required to install the HP System/e Rack Mount Kit: ■ Rails rear mounting brackets ■ Rail mounting hardware, shown next : (6) #8-32 x 5/16 inch Phillips pan-head screw with captive star lock washer (6) #8 Flat washer (6) M5 Torx head screw with captive lock washer (2) Rubber washer (4) M5 U-type Tinnerman clip Caution: For proper airflow, the SFP media side of the SAN Switch 2/32 faces the rear of the rack. This mounting allows air to enter from the front of the rack and to exhaust at the rear of the rack, similar to other rack-mounted equipment. This prevents switch overheating, which may cause it to fail. Use these steps to install the switch in the HP System/e rack. 1. Verify that all required hardware is available. 40 SAN Switch 2/32 Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Installing the SAN Switch 2/32
40
SAN Switch 2/32 Installation Guide
Installing the Switch in the Optional HP System/e Rack
This section provides instructions for installing the SAN Switch 2/32 in the
optional
HP System/e rack. The HP System/e Rack Kit consists of the following
items:
■
HP System/e Rack Rail Kit - pre-merger HP part number A7340-87901;
pre-merger Compaq part number QA-71AAA-GZ
■
HP System/e Rack Rail Kit Hardware - part number A7340-87902
The following hardware is required to install the HP System/e Rack Mount Kit:
■
Rails rear mounting brackets
■
Rail mounting hardware, shown next
:
Caution:
For proper airflow, the SFP media side of the SAN Switch 2/32
faces the rear of the rack. This mounting allows air to enter from the front of the
rack and to exhaust at the rear of the rack, similar to other rack-mounted
equipment. This prevents switch overheating, which may cause it to fail.
Use these steps to install the switch in the HP System/e rack.
1.
Verify that all required hardware is available.
(6) #8-32 x 5/16 inch Phillips pan-head screw with captive star
lock washer
(6) #8 Flat washer
(6) M5 Torx head screw with captive lock washer
(2) Rubber washer
(4) M5 U-type Tinnerman clip