HP StorageWorks 2/32 SAN switch 2/32 version 4.0.x installation guide - Page 30

Setting Up the Switch as a Stand-alone Unit, automatically runs a Power On Self-Test POST.

Get HP StorageWorks 2/32 - SAN Switch PDF manuals and user guides View all HP StorageWorks 2/32 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Installing the SAN Switch 2/32 Setting Up the Switch as a Stand-alone Unit Use these procedures for setting up the switch as a stand-alone unit. The following items are required for this setup: ■ SAN Switch 2/32 ■ AC power cords and cables supplied with the switch ■ Rubber mounting feet supplied with the switch 1. Place the SAN Switch 2/32 on a flat, sturdy surface like a table or lab bench. 2. Apply the rubber feet as follows: a. Clean the four depressions that are at each corner of the bottom of the switch to ensure they are free of dust. b. Place a rubber foot in each depression, with the adhesive side against the chassis, and press into place. Caution: Installing the rubber feet on the switch is recommended to help prevent the switch from accidentally sliding off the table or bench. 3. Connect the power cables to the SAN Switch 2/32 power connectors and to a power outlet. Ensure the power cable is routed so that it is not exposed to stress. 4. Turn on the power to the switch (flip the AC switch to "1"). The switch automatically runs a Power On Self-Test (POST). Caution: Do not connect the switch to the network until the IP address is correctly set. For instructions on how to set the IP address, see "Configuring SAN Switch 2/32 Network Addressing," later in this chapter. 30 SAN Switch 2/32 Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Installing the SAN Switch 2/32
30
SAN Switch 2/32 Installation Guide
Setting
Up the Switch as a Stand
-
alone Unit
Use these procedures for setting up the switch as a stand-alone unit. The following
items are required for this setup:
■
SAN Switch 2/32
■
AC power cords and cables supplied with the switch
■
Rubber mounting feet supplied with the switch
1.
Place the SAN Switch 2/32 on a flat, sturdy surface like a table or lab bench.
2.
Apply the rubber feet as follows:
a.
Clean the four depressions that are at each corner of the bottom of the
switch to ensure they are free of dust.
b.
Place a rubber foot in each depression, with the adhesive side against the
chassis, and press into place.
Caution:
Installing the rubber feet on the switch is recommended to help
prevent the switch from accidentally sliding off the table or bench.
3.
Connect the power cables to the SAN Switch 2/32 power connectors and to a
power outlet. Ensure the power cable is routed so that it is not exposed to
stress.
4.
Turn on the power to the switch (flip the AC switch to “1”). The switch
automatically runs a Power On Self-Test (POST).
Caution:
Do not connect the switch to the network until the IP address is
correctly set. For instructions on how to set the IP address, see “
Configuring
SAN Switch 2/32 Network Addressing
,” later in this chapter.