Brother International HE-800B Instruction Manual - English - Page 27

INSTALLATION, <100 V / 400 V system&gt, may occur.

Get Brother International HE-800B PDF manuals and user guides View all Brother International HE-800B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Operator 3. INSTALLATION (1) Power switch (2) Screws [2 pcs] 4145M 4758M (3) Transformer box (4) Transformer box plates [2 pcs] (5) Screw [with washer] (6) 3-pin power supply connector (7) Staples [6 pcs] (8) Cord clamps [2 pcs] (9) Power cord 1. Attach an appropriate plug to the power cord (9). (The green and yellow wire is the ground wire.) 2. Insert the power plug into a properly-grounded AC power supply. * The inside of the control box uses single-phase power. NOTE: • If the ground connection is not secure, electric shocks, operating errors or damage to electronic components such as P.C. boards may occur. • Take care when tapping in the staples (7) to make sure that they do not pierce the cords. • Do not use extension cords, otherwise machine operation problems may result. 3. Use the six screws to tighten the cover of the control box. Check that none of the cords are being clamped by the cover at this time. Green and yellow wire (ground wire) 4936M HE-800B 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
HE-800B
3. INSTALLATION
18
<100 V / 400 V system>
(1) Power switch
(2) Screws [2 pcs]
(3) Transformer box
(4) Transformer box plates [2 pcs]
(5) Screw [with washer]
(6) 3-pin power supply connector
(7) Staples [6 pcs]
(8) Cord clamps [2 pcs]
(9) Power cord
1. Attach an appropriate plug to the
power cord (9). (The green and
yellow wire is the ground wire.)
2. Insert
the
power
plug
into
a
properly-grounded AC power supply.
* The inside of the control box uses
single-phase power.
NOTE:
• If the ground connection is not
secure, electric shocks, operating
errors
or
damage
to
electronic
components such as P.C. boards
may occur.
• Take care when tapping in the
staples (7) to make sure that they do
not pierce the cords.
• Do
not
use
extension
cords,
otherwise
machine
operation
problems may result.
3. Use the six screws to tighten the
cover of the control box. Check that
none of the cords are being clamped
by the cover at this time.
Green and yellow wire
(ground wire)
4145M
4758M
4936M
Operator