Cisco ISE Software Configuration Guide - Page 11

Configuring OAM Management on Terminated VCs, SUMMARY STEPS - 1 1 release notes

Get Cisco ISE - Line Card ISE PDF manuals and user guides
UPC - 746320730097
View all Cisco ISE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card Step 4 Command or Action pvc [name] vpi/vci Step 5 Example: Router(config-if)# pvc 0/100 cbr pcr Router(config-if-vc)# cbr 155000 Purpose Specifies a PVC with the specified VPI and virtual circuit identifier (VCI). Specifies CBR shaping. The pcr value indicates the peak cell rate. The range is from 38 to 622,000 Kbps. Step 6 vbr-rt pcr scr burst Step 7 Example: Router(config-if-vc)# vbr-rt 100000 40000 200000 vbr-nrt pcr scr mbs Example: Router(config-if-vc)# vbr-nrt 100000 40000 200000 Step 8 ubr pcr Example: Router(config-if-vc)# ubr 100000 Note Use either Step 5, Step 6, Step 7, or Step 8. Specifies VBR-rt shaping. The pcr value indicates the peak cell rate, and its range is from 38 to 622,000 Kbps. The scr value indicates the sustainable cell rate, and its range is from 38 to pcr Kbps. The burst value indicates the burst size, in number of cells. Specifies VBR-nrt shaping. The pcr value indicates the peak cell rate, and its range is from 38 to 622,000 Kbps. The scr value indicates the sustainable cell rate, and its range is from 38 to pcr Kbps. The mbs value indicates the maximum burst size, in number of cells. Specifies UBR shaping. The pcr value indicates the peak cell rate, and its range is from 38 to 622,000 Kbps. Configuring OAM Management on Terminated VCs OAM may be enabled for PVC or SVC management on terminated VCs. To configure OAM management for an ATM Layer 3 PVC, perform the following procedure. SUMMARY STEPS 1. enable 2. configure terminal 3. interface atmslot/port.subinterface [point-to-point | multipoint] 4. pvc vpi/vci 5. oam-pvc manage 6. oam retry up-count down-count retry-frequency 7. oam-pvc manage cc {end | segment} [direction {both | sink | source}] [keep-vc-up [end aisrdi failure | seg aisrdi failure]] 8. oam retry cc {end | segment} [activation-count [deactivation-count [retry-frequency]]] Cisco IOS Release 12.0(27)S 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers
How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card
11
Cisco IOS Release 12.0(27)S
Configuring OAM Management on Terminated VCs
OAM may be enabled for PVC or SVC management on terminated VCs. To configure OAM management
for an ATM Layer 3 PVC, perform the following procedure.
SUMMARY STEPS
1.
enable
2.
configure
terminal
3.
interface atm
slot/port.subinterface
[
point-to-point
|
multipoint
]
4.
pvc
vpi/vci
5.
oam-pvc manage
6.
oam retry
up-count down-count retry-frequency
7.
oam-pvc manage
cc
{
end
|
segment
} [
direction
{
both
|
sink
|
source
}] [
keep-vc-up
[
end aisrdi
failure
|
seg aisrdi failure
]]
8.
oam retry
cc
{
end
|
segment
} [
activation-count
[
deactivation-count
[
retry-frequency
]]]
Step 4
pvc
[
name
]
vpi/vci
Example:
Router(config-if)# pvc 0/100
Specifies a PVC with the specified VPI and virtual circuit
identifier (VCI).
Step 5
cbr
pcr
Router(config-if-vc)# cbr 155000
Specifies CBR shaping.
The
pcr
value indicates the peak cell rate. The range is from
38 to 622,000 Kbps.
Note
Use either
Step 5
,
Step 6
,
Step 7
, or
Step 8
.
Step 6
vbr-rt
pcr scr burst
Example:
Router(config-if-vc)# vbr-rt 100000 40000
200000
Specifies VBR-rt shaping.
The
pcr
value indicates the peak cell rate, and its range is
from 38 to 622,000 Kbps. The
scr
value indicates the
sustainable cell rate, and its range is from 38 to
pcr
Kbps.
The burst value indicates the burst size, in number of cells.
Step 7
vbr-nrt
pcr scr mbs
Example:
Router(config-if-vc)# vbr-nrt 100000 40000
200000
Specifies VBR-nrt shaping.
The
pcr
value indicates the peak cell rate, and its range is
from 38 to 622,000 Kbps. The
scr
value indicates the
sustainable cell rate, and its range is from 38 to
pcr
Kbps.
The
mbs
value indicates the maximum burst size, in number
of cells.
Step 8
ubr
pcr
Example:
Router(config-if-vc)# ubr 100000
Specifies UBR shaping.
The
pcr
value indicates the peak cell rate, and its range is
from 38 to 622,000 Kbps.
Command or Action
Purpose