Cisco ISE Software Configuration Guide - Page 4

Layer 3-Specific Features, Sophisticated MQC classifications based on IP ACL/xACL, IP precedence/DSCP - sizing

Get Cisco ISE - Line Card ISE PDF manuals and user guides
UPC - 746320730097
View all Cisco ISE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

Information About the 4-Port ATM ISE Line Card Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers • F4 and F5 flows of operation, administration, and maintenance (OAM) cells and OAM management specified as requirements by [UNI 3.x] [I.610]. Layer 3-Specific Features • Supports up to 2047 traffic-shaped VC connections per interface.1 • Bidirectional OC-12c/STM-4c line rate for 64-byte packets (two cells) on all four ports. This is an aggregate line rate of approximately 2.8 million packets per second. • Bidirectional OC-3c/STM-1 full line rate for any packet size on all four ports. • Support for up to 120 distinct WRED profiles per interface. These profiles are configurable using Cisco IOS software. • ATM VC bundle management. • MPLS Traffic Engineering (TE), including Single Area (OSPF,ISIS), DS-TE (OSPF,ISIS), Autobandwidth, TE Metrics (OSPF,ISIS), TE Node Exclusion (OSPF,ISIS), Multiarea (OSPF,ISIS). • Support for thousands of ACL/xACL entries, including both ingress and egress for interfaces and subinterfaces. • Committed Access Rate (CAR), including CAR action continue, including both ingress and egress for interfaces and subinterfaces. • Policy-based routing (PBR) for interfaces and subinterfaces. • Border Gateway Protocol (BGP) policy accounting. • Unicast reversepath forwarding (uRPF) loose mode. • Sophisticated MQC classifications based on IP ACL/xACL, IP precedence/DSCP, MPLS EXP, QoS groups, and more. • IP and MPLS traffic marking • QoS Policy Propagation via BGP (QPPB) • Ingress IP-based traffic shaping. • Netflow, including sampled ingress/egress Netflow, aggregated Netflow, and MPLS-aware Netflow. • High Availability, including route processor redundancy (RPR), RPR+, and Stateful Switchover (SSO). • ATM OAM F5 continuity check. • MPLS virtual private network (VPN). • UNI 3.x and Interim Local Management Interface (ILMI). • Switched virtual circuit (SVC) support for point-to-point and point-to-multipoint connections. • Multicast packet replication. • ATM cell loss priority (CLP) bit setting. • MPLS VPN Inter-AS. • MPLS VPN carrier supporting carrier (CsC). Layer 2-Specific Features • Supports up to 2047 traffic-shaped VC connections per interface.2 1. Subject to overall system limitation and configuration. Cisco IOS Release 12.0(27)S 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers
Information About the 4-Port ATM ISE Line Card
4
Cisco IOS Release 12.0(27)S
•
F4 and F5 flows of operation, administration, and maintenance (OAM) cells and OAM management
specified as requirements by [UNI 3.x] [I.610].
Layer 3-Specific Features
•
Supports up to 2047 traffic-shaped VC connections per interface.
1
•
Bidirectional OC-12c/STM-4c line rate for 64-byte packets (two cells) on all four ports. This is an
aggregate line rate of approximately 2.8 million packets per second.
•
Bidirectional OC-3c/STM-1 full line rate for any packet size on all four ports.
•
Support for up to 120 distinct WRED profiles per interface. These profiles are configurable using
Cisco IOS software.
•
ATM VC bundle management.
•
MPLS Traffic Engineering (TE), including Single Area (OSPF,ISIS), DS-TE (OSPF,ISIS),
Autobandwidth, TE Metrics (OSPF,ISIS), TE Node Exclusion (OSPF,ISIS), Multiarea (OSPF,ISIS).
•
Support for thousands of ACL/xACL entries, including both ingress and egress for interfaces and
subinterfaces.
•
Committed Access Rate (CAR), including CAR action continue, including both ingress and egress
for interfaces and subinterfaces.
•
Policy-based routing (PBR) for interfaces and subinterfaces.
•
Border Gateway Protocol (BGP) policy accounting.
•
Unicast reversepath forwarding (uRPF) loose mode.
•
Sophisticated MQC classifications based on IP ACL/xACL, IP precedence/DSCP, MPLS EXP, QoS
groups, and more.
•
IP and MPLS traffic marking
•
QoS Policy Propagation via BGP (QPPB)
•
Ingress IP-based traffic shaping.
•
Netflow, including sampled ingress/egress Netflow, aggregated Netflow, and MPLS-aware Netflow.
•
High Availability, including route processor redundancy (RPR), RPR+, and Stateful Switchover
(SSO).
•
ATM OAM F5 continuity check.
•
MPLS virtual private network (VPN).
•
UNI 3.x and Interim Local Management Interface (ILMI).
•
Switched virtual circuit (SVC) support for point-to-point and point-to-multipoint connections.
•
Multicast packet replication.
•
ATM cell loss priority (CLP) bit setting.
•
MPLS VPN Inter-AS.
•
MPLS VPN carrier supporting carrier (CsC).
Layer 2-Specific Features
•
Supports up to 2047 traffic-shaped VC connections per interface.
2
1. Subject to overall system limitation and configuration.