Cisco ISE Software Configuration Guide - Page 78

Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers

Troubleshooting ATM Errors on the 4-Port ATM ISE Line Card

78

Cisco IOS Release 12.0(27)S

show controller traffic

Any packets received on nonexistence VCs will be displayed in the

show atm traffic

RP command.

router#

show atm traffic

3523 Input packets

3510 Output packets

0 Broadcast packets

0

Packets received on non-existent VC

0 Packets attempted to send on non-existent VC

3507 OAM cells received

F5 InEndloop: 0, F5 InSegloop: 0, F5 InAIS: 0, F5 InRDI: 0

F4 InEndloop: 3507, F4 InSegloop: 0, F4 InAIS: 0, F4 InRDI: 0

3507 OAM cells sent

F5 OutEndloop: 0, F5 OutSegloop: 0,

F5 OutAIS: 0

F5 OutRDI: 0

F4 OutEndloop: 3507, F4 OutSegloop: 0,

F4 OutRDI: 0

F4 OutAIS: 0

0 OAM cell drops

show controller atm

To display the ATM statistics on the line card, use the line card

show controller atm

privileged EXEC

command. The available

show controller atm

counters are described in

Table 9 on page 79

.

Router#

exec slot 1 show controller atm 1 traffic

VCID

InPkts

InBytes

PktsInSW

InOams

OutPkts

OutBytes

1

78278986

4227058178

0

0

82600440 4460416714

SAR Counters:

tx_packets

: 82600440

tx_bytes

: 4460416714

tx_total_resource_errs

:

0

tx_total_other_errs

:

0

tx_wred_thresh_drops

:

0

tx_wred_random_drops

:

0

rx_packets

: 78278986

rx_bytes

: 4227058178

rx_total_resource_errs

:

0

rx_total_other_errs

:

0

rx_buffer_exhaust_errs

:

0

rx_CRC32_errors

:

0

rx_packet_abort_errs

:

0

rx_trailer_len_errs

:

0

rx_mps_errors

:

0

rx_reassembly_timeout

:

0

The following are per-SAR counters:

Reassembly SAR:

sys_rx_unopen_vc_cls

:

89169

sys_tx_unopen_vc_cls

:

0

sys_ecc_errors

:

0

sys_ecc_and_addr

:

0xFFFFFFF

sys_ecc_or_addr

: 0x00000000

Segmentation SAR:

sys_rx_unopen_vc_cls

:

0

sys_tx_unopen_vc_cls

:

0

sys_ecc_errors

:

0

sys_ecc_and_addr

:

0xFFFFFFFF

sys_ecc_or_addr

: 0x00000000

Abort

The number of packet reassemblies that failed because of receiving a trailer length

of 0.

Output errors

The total number of packets that were not transmitted because of any error other

than resource exhaustion. This includes malformed packets, CRC errors, and so on.

Table 8

show interfaces Error Counter Descriptions (continued)

Error Counter

Description

Section	Page
Software Configuration of ATM ISE Line Cards for Cisco 12000 Series Routers	1
Contents	1
Prerequisites for the 4-Port ATM ISE Line Card	2
Restrictions for the 4-Port ATM ISE Line Card	2
Information About the 4-Port ATM ISE Line Card	3
Features of the 4-Port ATM ISE Line Card	3
Layer 3-Specific Features	4
Layer 2-Specific Features	4
How to Perform a Basic Configuration of the 4-Port ATM ISE Line Card	5
Configuring an ATM Interface	5
Default Interface Configuration	5
Configuration Basics	6
Configuring UNI and NNI Cell Support	7
Troubleshooting Tips	7
How to Configure Layer 3 Terminated VCs on the 4-Port ATM ISE Line Card	8
Configuring Layer 3 Terminated Virtual Circuits	8
Troubleshooting Tips	9
Configuring ATM Shaping on Terminated VCs	9
Restrictions	9
Configuring OAM Management on Terminated VCs	11
Configuring Quality of Service on Terminated VCs	14
Configuring Traffic Policing	14
Configuring a Per-VC Queue Limit	16
Configuring Per-VC WRED	18
Configuring Per-VC MDRR and Low Latency Queueing	20
Configuring the set Commands	23
Troubleshooting Tips	27
Configuring and Managing VC Bundles	28
Creating a VC Bundle	28
Applying Bundle-Level Parameters	28
Committing a VC to a Bundle	30
Applying Parameters to Individual VCs	30
VC Bundle Examples	32
Troubleshooting Tips	34
Configuring Bridged PVCs	35
How to Configure AToM VCs on the 4-Port ATM ISE Line Card	35
Configuring Layer 2 AToM Virtual Circuits	35
Troubleshooting Tips	36
Configuring AToM VCs	36
Prerequisites	37
Configuring ATM AAL5 over MPLS	37
Configuring ATM Cell Relay over MPLS on PVCs	38
Configuring ATM Cell Relay over MPLS on PVPs	40
Configuring ATM Cell Relay over MPLS on a Port	41
Configuring ATM Cell Packing over MPLS on PVCs	42
Configuring ATM Cell Packing over MPLS on PVPs	44
Configuring ATM Cell Packing over MPLS on a Port	45
Configuring OAM Emulation on AToM VCs	47
Troubleshooting Tips	49
Configuring ATM Shaping on AToM VCs	49
Restrictions	50
Configuring Cell Relay over MPLS on PVCs	50
Configuring Cell Relay over MPLS on PVPs	52
Configuring Cell Packing over MPLS on PVCs	55
Configuring Cell Packing over MPLS on PVPs	57
Configuring AAL5 over MPLS on PVCs	60
Troubleshooting Tips	62
Configuring Cell-Based Traffic Policing on AToM VCs	63
Restrictions	63
Configuring CBR or UBR.1 Policing	64
Configuring VBR.1 Policing	65
Configuring VBR.2 Policing	67
Configuring VBR.3 Policing	69
Attaching a Service Policy to a PVC	72
Troubleshooting Tips	73
Configuring Experimental Mapping	73
Configuring Experimental Bits on PVCs	73
Configuring Experimental Bits on a Port	75
Troubleshooting ATM Errors on the 4-Port ATM ISE Line Card	76
Troubleshooting Commands	77
show interfaces atm	77
show controller traffic	78
show controller atm	78
Obtaining Per-VC Counters	81
Debugging Unexpected TX Drops on a VC	82
Upgrading the FPGA Image	83
Configuring Modular QoS CLI	84
Defining a Traffic Class	84
Using the class-map match-any and class-map match-all Commands	85
Creating a Traffic Policy	85
Commands for Egress Traffic	86
Commands for Ingress Traffic	88
Attaching a Traffic Policy to a PVC	90
Additional References	91
Related Documents	91
Standards	91
MIBs	91
RFCs	92
Technical Assistance	92
Command Reference	92
police rate	93
random-detect dscp	97

Cisco ISE Software Configuration Guide - Page 78

show controller traffic, Error Counter, Description

Page 78 highlights