Dell PowerEdge MX750c EMC Installation and Service Manual - Page 35

Removing the drive from the drive carrier, Installing drive carrier

Get Dell PowerEdge MX750c PDF manuals and user guides View all Dell PowerEdge MX750c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

NOTE: Ensure that the drive carrier's release handle is in the open position before inserting the carrier into the slot. 1. Follow the safety guidelines listed in the Safety instructions. 2. Remove the drive carrier or remove the drive blank when you want to assemble the drives in to the system. Steps 1. Slide the drive carrier into the drive slot. 2. Close the drive carrier release handle to lock the drive in place. Figure 24. Installing drive carrier Removing the drive from the drive carrier Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Remove the drive carrier. Steps 1. Using the Phillips #1 screwdriver, remove the screws from the slide rails on the drive carrier. NOTE: If the hard drive or SSD carrier has Torx screw, use Torx 6 (for 2.5-inch drive) or Torx 8 (for 3.5-inch drive) screwdriver to remove the drive. 2. Lift the drive out of the drive carrier. Installing and removing system components 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
NOTE:
Ensure that the drive carrier's release handle is in the open position before inserting the carrier into the slot.
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Remove the drive carrier or remove the drive blank when you want to assemble the drives in to the system.
Steps
1.
Slide the drive carrier into the drive slot.
2.
Close the drive carrier release handle to lock the drive in place.
Figure 24. Installing drive carrier
Removing the drive from the drive carrier
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Remove the drive carrier
.
Steps
1.
Using the Phillips #1 screwdriver, remove the screws from the slide rails on the drive carrier.
NOTE:
If the hard drive or SSD carrier has Torx screw, use Torx 6 (for 2.5-inch drive) or Torx 8 (for 3.5-inch drive)
screwdriver to remove the drive.
2.
Lift the drive out of the drive carrier.
Installing and removing system components
35