Dell PowerEdge MX750c EMC Installation and Service Manual - Page 84

Installing the Mezzanine card, Removing the Mezzanine-B card

Get Dell PowerEdge MX750c PDF manuals and user guides View all Dell PowerEdge MX750c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

Figure 77. Removing the Mezzanine-B card Next steps 1. Install the Mezzanine card. 2. Follow the procedure listed in After working inside your system. Installing the Mezzanine card Prerequisites 1. Follow the safety guidelines listed in Safety Instructions. 2. Follow the procedure listed in Before working inside your system. NOTE: Mezzanine B card is supported only on dual-processor configuration. Steps 1. Align the connector on the Mezzanine card with the connector on the system board. 2. Place the Mezzanine card on the connector and press the blue touch point firmly until it is fully seated. 3. Using the Phillips #2 screwdriver, tighten the captive screws on the Mezzanine card. 84 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
Figure 77. Removing the Mezzanine-B card
Next steps
1.
Install the Mezzanine card
.
2.
Follow the procedure listed in
After working inside your system
.
Installing the Mezzanine card
Prerequisites
1.
Follow the safety guidelines listed in
Safety Instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
NOTE:
Mezzanine B card is supported only on dual-processor configuration.
Steps
1.
Align the connector on the Mezzanine card with the connector on the system board.
2.
Place the Mezzanine card on the connector and press the blue touch point firmly until it is fully seated.
3.
Using the Phillips #2 screwdriver, tighten the captive screws on the Mezzanine card.
84
Installing and removing system components