Dell PowerEdge MX750c EMC Installation and Service Manual - Page 73

Installing the Jumbo PERC card, Removing the Jumbo PERC card H745P MX

Get Dell PowerEdge MX750c PDF manuals and user guides View all Dell PowerEdge MX750c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Figure 66. Removing the Jumbo PERC card (H745P MX) NOTE: The Jumbo PERC card controls the internal drives, and the storage sled drives mapped to the storage controller. Next steps 1. Install the Jumbo PERC card (H745P MX). Installing the Jumbo PERC card Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. NOTE: Jumbo PERC card is supported only on dual-processor configuration. Steps 1. Remove the connector cap on the I/O connector from the Jumbo PERC card. 2. Pull the blue pull tag to raise the lever on the Jumbo PERC card. 3. Align the Jumbo PERC card with the slots on the system board. 4. Press the Jumbo PERC card firmly until it is fully seated. 5. Close the lever on the Jumbo PERC card. Installing and removing system components 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
Figure 66. Removing the Jumbo PERC card (H745P MX)
NOTE:
The Jumbo PERC card controls the internal drives, and the storage sled drives mapped to the storage controller.
Next steps
1.
Install the Jumbo PERC card (H745P MX)
.
Installing the Jumbo PERC card
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
NOTE:
Jumbo PERC card is supported only on dual-processor configuration.
Steps
1.
Remove the connector cap on the I/O connector from the Jumbo PERC card.
2.
Pull the blue pull tag to raise the lever on the Jumbo PERC card.
3.
Align the Jumbo PERC card with the slots on the system board.
4.
Press the Jumbo PERC card firmly until it is fully seated.
5.
Close the lever on the Jumbo PERC card.
Installing and removing system components
73