Dell PowerEdge MX750c EMC Installation and Service Manual - Page 36

Installing the drive into the drive carrier

Get Dell PowerEdge MX750c PDF manuals and user guides View all Dell PowerEdge MX750c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Figure 25. Removing a drive from drive carrier Next steps Replace the drive into the drive carrier. Installing the drive into the drive carrier Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Remove the drive blank. NOTE: When installing a drive into the drive carrier, ensure that the screws are torqued to 4 in-lbs. Steps 1. Insert the drive into the drive carrier with the drive connector facing towards the rear of the carrier. 2. Align the screw holes on the drive with the screw holes on the drive carrier. 3. Using the Phillips #1 screwdriver, secure the drive to the drive carrier with the screws. NOTE: If the hard drive or SSD carrier has Torx screw, use Torx 6 (for 2.5-inch drive) screwdriver to install the drive. 36 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
Figure 25. Removing a drive from drive carrier
Next steps
Replace the drive into the drive carrier
.
Installing the drive into the drive carrier
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Remove the drive blank
.
NOTE:
When installing a drive into the drive carrier, ensure that the screws are torqued to 4 in-lbs.
Steps
1.
Insert the drive into the drive carrier with the drive connector facing towards the rear of the carrier.
2.
Align the screw holes on the drive with the screw holes on the drive carrier.
3.
Using the Phillips #1 screwdriver, secure the drive to the drive carrier with the screws.
NOTE:
If the hard drive or SSD carrier has Torx screw, use Torx 6 (for 2.5-inch drive) screwdriver to install the
drive.
36
Installing and removing system components