Dell PowerEdge MX750c EMC Installation and Service Manual - Page 50

Control panel, Removing the control panel

Get Dell PowerEdge MX750c PDF manuals and user guides View all Dell PowerEdge MX750c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Figure 44. Installing the drive cage Next steps 1. Install the drive backplane. 2. Install all the drives. 3. Follow the procedure listed in After working inside your system. Control panel This is a service technician replaceable part only. Removing the control panel Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove all the drives. 4. Remove the drive cage. Steps 1. Releasing the blue latches, pull the blue strap to disconnect the control panel cable connected to the system board. 2. Using the Phillips #1 screwdriver, remove the screws that secure the control panel to the system. 3. Holding the control panel, remove the control panel along with the cable from the system. NOTE: The numbers on the image do not depict the exact steps. The numbers are for representation of sequence. 50 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
Figure 44. Installing the drive cage
Next steps
1.
Install the drive backplane
.
2.
Install all the drives
.
3.
Follow the procedure listed in
After working inside your system
.
Control panel
This is a service technician replaceable part only.
Removing the control panel
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove all the drives
.
4.
Remove the drive cage
.
Steps
1.
Releasing the blue latches, pull the blue strap to disconnect the control panel cable connected to the system board.
2.
Using the Phillips #1 screwdriver, remove the screws that secure the control panel to the system.
3.
Holding the control panel, remove the control panel along with the cable from the system.
NOTE:
The numbers on the image do not depict the exact steps. The numbers are for representation of sequence.
50
Installing and removing system components