Dell PowerEdge MX750c EMC Installation and Service Manual - Page 63

Lift up the TIM break lever, Aligning pin 1 marks of processor with tray

Get Dell PowerEdge MX750c PDF manuals and user guides View all Dell PowerEdge MX750c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

3. Holding the processor by its edges, lift the processor away from the retaining clip, and then place the processor connector side down on the processor tray. Ensure pin 1 marks are aligned. Figure 52. Lift up the TIM break lever Figure 53. Aligning pin 1 marks of processor with tray NOTE: Ensure that to return the TIM break lever back to its original position. 4. Using your thumb and index finger, first hold the retaining clip release tab at the pin 1 connector, pull out the tip of the retaining clip release tab, and then lift the retaining clip partially from the heat sink. 5. Repeat the procedure at the remaining three corners of the retaining clip. 6. After all the corners are released from the heat sink, lift the retaining clip from the pin 1 corner of the heat sink. Installing and removing system components 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
3.
Holding the processor by its edges, lift the processor away from the retaining clip, and then place the processor connector
side down on the processor tray. Ensure pin 1 marks are aligned.
Figure 52. Lift up the TIM break lever
Figure 53. Aligning pin 1 marks of processor with tray
NOTE:
Ensure that to return the TIM break lever back to its original position.
4.
Using your thumb and index finger, first hold the retaining clip release tab at the pin 1 connector, pull out the tip of the
retaining clip release tab, and then lift the retaining clip partially from the heat sink.
5.
Repeat the procedure at the remaining three corners of the retaining clip.
6.
After all the corners are released from the heat sink, lift the retaining clip from the pin 1 corner of the heat sink.
Installing and removing system components
63