Dell PowerEdge MX750c EMC Installation and Service Manual - Page 67

Installing the processor and heat sink module, Installing the heat sink onto the processor

Get Dell PowerEdge MX750c PDF manuals and user guides View all Dell PowerEdge MX750c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

NOTE: Ensure latching features on processor retaining clip and heat sink are aligned during assembly. Figure 59. Installing the heat sink onto the processor Next steps 1. Install the processor and heat sink module. 2. Install the air shroud. 3. Follow the procedure listed in After working inside your system. Installing the processor and heat sink module Prerequisites CAUTION: Never remove the heat sink from a processor unless you intend to replace the processor. The heat sink is necessary to maintain proper thermal conditions. 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in the Before working inside the system. 3. Remove the air shroud. 4. If installed, remove the processor dust cover. Steps 1. Set the Anti-Tilt wires to the unlocked position on the heat sink (inward position). 2. Align the pin 1 indicator of the heat sink to the system board, and then place the processor and heat sink on the processor socket. CAUTION: To avoid damaging the fins on the heat sink, do not press down on the heat sink fins. Installing and removing system components 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
NOTE:
Ensure latching features on processor retaining clip and heat sink are aligned during assembly.
Figure 59. Installing the heat sink onto the processor
Next steps
1.
Install the processor and heat sink module
.
2.
Install the air shroud
.
3.
Follow the procedure listed in
After working inside your system
.
Installing the processor and heat sink module
Prerequisites
CAUTION:
Never remove the heat sink from a processor unless you intend to replace the processor. The heat
sink is necessary to maintain proper thermal conditions.
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside the system
.
3.
Remove the air shroud
.
4.
If installed, remove the processor dust cover.
Steps
1.
Set the Anti-Tilt wires to the unlocked position on the heat sink (inward position).
2.
Align the pin 1 indicator of the heat sink to the system board, and then place the processor and heat sink on the processor
socket.
CAUTION:
To avoid damaging the fins on the heat sink, do not press down on the heat sink fins.
Installing and removing system components
67