Dell PowerEdge MX750c EMC Installation and Service Manual - Page 38

Removing drive backplane, x 2.5-inch SAS/SATA backplane

Get Dell PowerEdge MX750c PDF manuals and user guides View all Dell PowerEdge MX750c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

5. BP_DST_PA1 (PCIe cable connector ) Figure 28. 6 x 2.5-inch SAS/SATA backplane 1. BP_DST_SA1 (SAS/SATA cable connector) 2. BP_PWR_1 (Power cable connector) Figure 29. 4 x 2.5-inch universal backplane 1. BP_PWR_1 (Power cable connector) 2. BP_DST_PB1 (PCIe cable connector) 3. BP_DST_SA1 (SAS/SATA cable connector) 4. BP_DST_PA1 (PCIe cable connector ) Removing drive backplane Prerequisites CAUTION: To prevent damage to the drives and backplane, remove the drives from the system before removing the backplane. CAUTION: Note the number of each drive and temporarily label them before you remove the drive so that you can reinstall them in the same location. NOTE: The procedure to remove the backplane is similar for all backplane configurations. 1. Follow the safety guidelines listed in Safety Instructions. 2. Follow the procedure listed in Before working inside your system. 3. Disconnect the drive backplane cables from the connectors on the system board. 4. Remove all the drives. Steps 1. Holding the drive backplane by the edges, lift it upwards to disengage the backplane from the guide pins. 2. Lift the backplane out of the sled. 38 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
5.
BP_DST_PA1 (PCIe cable connector )
Figure 28. 6 x 2.5-inch SAS/SATA backplane
1.
BP_DST_SA1 (SAS/SATA cable connector)
2.
BP_PWR_1 (Power cable connector)
Figure 29. 4 x 2.5-inch universal backplane
1.
BP_PWR_1 (Power cable connector)
2.
BP_DST_PB1 (PCIe cable connector)
3.
BP_DST_SA1 (SAS/SATA cable connector)
4.
BP_DST_PA1 (PCIe cable connector )
Removing drive backplane
Prerequisites
CAUTION:
To prevent damage to the drives and backplane, remove the drives from the system before removing
the backplane.
CAUTION:
Note the number of each drive and temporarily label them before you remove the drive so that you
can reinstall them in the same location.
NOTE:
The procedure to remove the backplane is similar for all backplane configurations.
1.
Follow the safety guidelines listed in
Safety Instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
Disconnect the drive backplane cables from the connectors on the system board.
4.
Remove all the drives
.
Steps
1.
Holding the drive backplane by the edges, lift it upwards to disengage the backplane from the guide pins.
2.
Lift the backplane out of the sled.
38
Installing and removing system components