HP 6125XLG R2306-HP 6125XLG Blade Switch FCoE Configuration Guide
HP 6125XLG Manual
View all HP 6125XLG manuals
Add to My Manuals
Save this manual to your list of manuals |
HP 6125XLG manual content summary:
- HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 1
HP 6125XLG Blade Switch FCoE Configuration Guide Part number: 5998-3726 Software version: Release 2306 Document version: 6W100-20130912 - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 2
, or use of this material. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 3
2 Communication flow 3 VSAN 4 FC zone 4 FCoE 5 Basic concepts 5 How FCoE works 7 FCoE modes 8 FCF mode 9 NPV mode 9 Protocols and standards 10 Configuring an FCoE mode 11 FCoE features supported in different FCoE modes 11 Configuration procedure 11 Configuring VFC interfaces and FIP 13 - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 4
procedure 32 Verifying the configurations 36 Dynamic fabric building configuration example 37 Network requirements 37 Configuration procedure 38 Verifying the configurations 45 Configuring VSAN 47 VSAN fundamentals 47 Trunk VSAN in an FC network 47 Trunk VSAN in an FCoE network 47 Creating - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 5
Distributing zones 73 Zone merge 75 Access control 77 FC zone configuration task list 77 Configuring zone aliases 78 Configuring zones 78 Configuring zone sets 79 Configuring the default zone policy 79 Configuring zone distribution and merge types 79 Activating a zone set and distributing - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 6
100 FC tracert configuration example 100 Network requirements 100 Configuration procedure 100 Appendixes 105 Appendix A Fabric address assignment 105 Appendix B Well-known fabric addresses 105 Support and other resources 107 Contacting HP 107 Subscription service 107 Related information - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 7
overview The switch supports FCoE only when operating in advanced mode (the default). For more information about system operating modes, see Fundamentals Configuration Guide. HP recommends that you set the delay for the IRF ports to report a link down event as 0 on IRF member devices connected into - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 8
• A fabric refers to a transmission network comprising FC switches. FC protocol The servers, FC switches, and disk devices in an FC SAN must all support FC. Basic concepts WWN The world wide name (WWN) is a 64-bit address that identifies a fabric or an entity (such as an FC switch, node, or port) in - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 9
information about NP_Port, see "Configuring NPV." E_Ports connect FC switches to form a fabric, and F_Ports connect the nodes to FC switches in the fabric. Communication flow FC switches provide data transmission services. Through FC switches, a server sends instructions and data to disk devices - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 10
last hop forwards the FC frame to the destination disk device. NOTE: A FIB table is generated by the FC switch through calculation based on the FC routing protocol or configured static routes. VSAN In actual applications, the data is insecure because the data of all users is transmitted in the same - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 11
to solve this problem. FCoE is a protocol that carries FC over Ethernet. In an FCoE solution, the server uses an FCoE-capable Ethernet adapter, and the FCoE switch (FCoE forwarder) integrates the functions of both the traditional IP switch and FCF switch. FCoE reduces the number of network adapters - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 12
the FC frame. An FCoE frame uses Ethernet II encapsulation, which has the following fields in the Ethernet header: • EtherType 0x8906. • Destination MAC address/source MAC address-For a switch, it is the FCoE MAC address of the switch (which can be displayed by using the display fcoe command). For - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 13
. • After the virtual link is established, the FCF switch encapsulates the FC frame in an FCoE frame and sends it out. • After receiving the FCoE frame, the FCF switch removes its Ethernet header to send the original FC frame to the upper layer for processing. How FIP works FIP sets up and maintains - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 14
fcoe fka-adv-period command and defaults to 8 seconds. 4. After receiving the Discovery Advertisements, the ENode determines the FCF switch with frame to that switch for login. 5. After receiving the FLOGI request frame, the FCF checks whether the source MAC address matches its learned or bound FCoE - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 15
on a lossless Ethernet network. The FCoE virtual link between the ENode and FCF switch connects a VN interface to a VFC interface, and the FCoE virtual link between FCF switches connects two VFC interfaces. Each FCF switch is assigned a domain ID. Each FC SAN supports a maximum number of 239 domain - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 16
to nodes and as a node to the core switch. For more information about NPV, see "Configuring NPV." Protocols and standards • FC-FS-3, Fibre Channel - Framing and Signaling - 3 • FC-SW-5, Fibre Channel - Switch Fabric - 5 • FC-LS-2, Fibre Channel - Link Services - 2 • FC-GS-6, Fibre Channel - Generic - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 17
only when operating in advanced mode. For more information about system operating modes, see Fundamentals Configuration Guide. FCoE features supported in different FCoE modes The switch supports two FCoE modes: FCF mode and NPV mode. Each mode has different features as shown in Table 1. You can - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 18
Step 3. Display the FCoE mode of the switch. Command display fcoe-mode Remarks This command can be executed in any view. 12 - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 19
interface-type specified Ethernet interface. interface-number [ mac mac-address ] 5. Assign the VFC interface to the specified VSAN as a trunk port. port trunk vsan vsan-id 6. (Optional.) Configure a description for the VFC interface. description text Remarks N/A N/A By default, a VFC interface - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 20
for the VFC interface. 8. Bring up the VFC interface. Command default undo shutdown Remarks N/A By default, a VFC interface is up. Enabling FCoE for a VLAN and mapping a VSAN to the VLAN When you use a VFC interface to transmit packets, the Ethernet interface bound to the VFC interface can allow - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 21
Step 1. Enter system view. 2. Configure an FC-MAP value. Command system-view fcoe fcmap fc-map Remarks N/A The default setting is 0x0EFC00. Configuring the FKA advertisement period value The FKA advertisement period determines the length of time it takes the switch to detect the disconnection of - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 22
Step 1. Enter system view. 2. Enter VFC interface view. 3. Configure the FCF priority for the VFC interface. Command system-view interface vfc interface-number fcoe fcf-priority priority Remarks N/A N/A The default setting is 128. The configuration takes effect on a VFC interface only when it - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 23
DCBX on the connecting Ethernet interface. For information about configuring DCBX, see Layer 2-LAN Switching Configuration Guide. Configuration procedure This section describes the configurations for VFC interfaces and FIP on the FCF switch. 1. Configure Switch A: # Configure Switch A to operate in - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 24
Ethernet frame header ACL numbered 4000, and configure two rules to match FCoE frames (protocol type 0x8906) and FIP frames (protocol type 0x8914). [SwitchA] acl number quit # Configure the mapping from 802.1p priority 3 to local precedence 3 in the outbound direction. (This is the default mapping, - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 25
link-type trunk [SwitchA-Ten-GigabitEthernet1/1/6] port trunk permit vlan 20 [SwitchA-Ten-GigabitEthernet1/1/6] quit # Enable FCoE for VLAN 20 and map VLAN 20 to VSAN 10. [SwitchA] vlan 20 [SwitchA-vlan20] fcoe enable vsan 10 2. Configure Switch B: # Configure Switch B to operate in advanced mode - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 26
VFC 2, and configure it to operate in E mode. [SwitchB] interface vfc 2 [SwitchB-Vfc2] fc mode e # Bind interface VFC 2 to interface Ten-GigabitEthernet 1/1/6, and assign it to VSAN 10 as a trunk port. [SwitchB-Vfc2] bind interface ten-gigabitethernet 1/1/6 [SwitchB-Vfc2] port trunk vsan 10 - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 27
node connected to the fabric. You can build a fabric through one of the following modes: • Static mode-You must manually assign domain IDs to all switches in the network, and then each switch assigns FC addresses to the N_Ports connected to it. The static mode avoids network flappings, but it is - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 28
Each domain must have a domain ID. An FCF switch can automatically assign domain IDs. Alternatively, you can manually configure static domain IDs. • If you manually configure static domain IDs, you must assign a unique domain ID to each switch in the fabric. • If domain IDs are dynamically assigned - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 29
switch assigns the smallest available Area_ID and Port_ID to the N_Port. Fabric setup configuration task list When you set up a fabric, HP configuration function. When statically building a fabric, you must manually configure the fabric name, and make sure all switches in the fabric are configured - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 30
the fabric configuration function on switches. To statically set up a fabric, you must disable the fabric configuration function on switches and manually configure domain IDs for the switches. To enable or disable the fabric configuration function: Step 1. Enter system view. Command system-view - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 31
VSAN view. Command system-view vsan vsan-id 3. Configure a fabric name. fabric-name name Remarks N/A N/A By default, the fabric name is null. If the user does not configure a fabric name, the switch WWN is used as the fabric name after FCoE is enabled. Setting the switch priority The priority - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 32
: Step 1. Enter system view. 2. Enter VSAN view. 3. Configure a priority value for the switch. Command system-view vsan vsan-id priority value Remarks N/A N/A By default, the priority value of a switch is 128. Configuring the allowed domain ID list Configuring the allowed domain ID list has an - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 33
on an NPV switch. To bind the WWN of an N_Port to an FC address: Step 1. Enter system view. 2. Enter VSAN view. Command system-view vsan vsan-id 3. Bind the WWN of an wwn wwn-value area-port-id N_Port to an FC address. area-port-id-value Remarks N/A N/A By default, no binding is configured. If - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 34
period for the VSAN. 5. Configure the resource allocation timeout period for the VSAN. Command system-view vsan vsan-id timer distributed-services value timer error-detect value timer resource-allocation value Remarks N/A N/A By default, the distributed service timeout period is 5000 milliseconds - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 35
N/A By default, the auto fabric reconfiguration function is disabled. Manually initiating the fabric reconfiguration Step 1. Enter system view. 2. Enter VSAN view. 3. Initiate the fabric reconfiguration. Command system-view vsan vsan-id domain restart [ disruptive ] Configuring a VFC interface - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 36
-id Remarks N/A N/A By default, a VFC interface does not reject the received RCF requests. Configuring and obtaining FC4 information of nodes After a node registers with a switch through a FLOGI, the node sends a name service registration request to the switch for registering extended information - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 37
SCSI-FCP information. Command system-view vsan vsan-id fc name-service auto-discovery Remarks N/A N/A By default, auto discovery of SCSI-FCP information is enabled. Configuring the default FC4 information for a node If a node does not register FC4 information and the switch fails to obtain SCSI - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 38
Configuration procedure 1. Configure Switch A: # Configure Switch A to operate in advanced mode, save the configuration, and reboot Switch A. (Skip this step if the switch an Ethernet frame header ACL numbered 4000, and configure two rules to match FCoE frames (protocol type 0x8906) and FIP frames ( - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 39
number a behavior named app_b, and configure the action of marking packets Configure the mapping from 802.1p priority 3 to local precedence 3 in the outbound direction. (This is the default 1p priority 3, and configure Ten-GigabitEthernet 1/1/5 to # Create interface VFC 1, configure it to operate in F - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 40
[SwitchA-Ten-GigabitEthernet1/1/6] port trunk permit vlan 10 [SwitchA-Ten-GigabitEthernet1/1/6] quit # Enable FCoE for VLAN 10 and map VLAN 10 to VSAN 1. [SwitchA] vlan 10 [SwitchA-vlan10] fcoe enable vsan 1 [SwitchA-vlan10] quit 2. Configure Switch B: # Configure Switch B to operate in advanced - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 41
Ethernet frame header ACL numbered 4000, and configure two rules to match FCoE frames (protocol type 0x8906) and FIP frames (protocol type 0x8914). [SwitchB] acl number quit # Configure the mapping from 802.1p priority 3 to local precedence 3 in the outbound direction. (This is the default, and you - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 42
Ten-GigabitEthernet1/1/6] port trunk permit vlan 10 [SwitchB-Ten-GigabitEthernet1/1/6] quit # Enable FCoE for VLAN 10 and map VLAN 10 to VSAN 1. [SwitchB] vlan 10 [SwitchB-vlan10] fcoe enable vsan 1 [SwitchB-vlan10] quit Verifying the configurations 1. Verify the configurations on Switch A. [SwitchA - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 43
time information: Priority: 128 No interfaces available. The output shows that the domain configuration is complete and that the runtime domain ID of Switch A is 1. 2. Verify the configurations on Switch B. [SwitchB] display fc domain vsan 1 Domain Information of VSAN 1: Running time information - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 44
changed, please save the configuration and reboot the system to make it effective. # Configure Switch A to operate in FCF mode, and enable the fabric configuration function in VSAN 1 (optional, because this function is enabled by default). system-view [SwitchA] fcoe-mode fcf [SwitchA] vsan - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 45
trunk port. [SwitchA-Vfc2] bind interface ten-gigabitethernet 1/1/6 [SwitchA-Vfc2] port trunk vsan default). system-view [SwitchB] fcoe-mode fcf [SwitchB] vsan 1 [SwitchB-vsan1] domain configure enable # Set the switch priority to 1, so that Switch B can be selected as the principal switch - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 46
changed, please save the configuration and reboot the system to make it effective. # Configure Switch C to operate in FCF mode, and enable the fabric configuration function in VSAN 1 (optional, because this function is enabled by default). system-view [SwitchB] fcoe-mode fcf [SwitchC] vsan - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 47
the switch may Ethernet frame header ACL numbered 4000, and configure two rules to match FCoE frames (protocol type 0x8906) and FIP frames (protocol type 0x8914). [SwitchC] acl number Configure the mapping from 802.1p priority 3 to local precedence 3 in the outbound direction. (This is the default - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 48
1/1/5 to VLAN 10 as a trunk port. [SwitchC] interface ten-gigabitethernet 1/1/5 [SwitchC-Ten-GigabitEthernet1/1/5] port link-type trunk [SwitchC-Ten-GigabitEthernet1/1/5] port trunk permit vlan 10 [SwitchC-Ten-GigabitEthernet1/1/5] quit # Create interface VFC 2, and configure it to operate in E mode - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 49
dot1-tlv dcbx [SwitchD-Ten-GigabitEthernet1/1/6] quit # Create an Ethernet frame header ACL numbered 4000, and configure two rules to match FCoE frames (protocol type 0x8906) and FIP frames (protocol type 0x8914). [SwitchD] acl number 4000 [SwitchD-acl-ethernetframe-4000] rule permit type 8906 ffff - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 50
/1/6] quit # Configure the mapping from 802.1p priority 3 to local precedence 3 in the outbound direction. (This is the default, and you and assign it to VSAN 1 as a trunk port. [SwitchD-Vfc1] bind interface ten-gigabitethernet 1/1/5 [SwitchD-Vfc1] port trunk vsan 1 [SwitchD-Vfc1] quit # Assign - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 51
/1/6] port trunk permit vlan 10 [SwitchD-Ten-GigabitEthernet1/1/6] quit # Enable FCoE for VLAN 10 and map VLAN 10 to VSAN 1. [SwitchD] vlan 10 [SwitchD-vlan10] fcoe enable vsan 1 [SwitchD-vlan10] quit Verifying the configurations # Display the domain information of VSAN 1 on Switch A. [SwitchA - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 52
The output shows that Switch B becomes the principal switch and assigns the smallest domain ID 1 to itself. 46 - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 53
the frames. A switch can use the same physical interface to support multiple VSANs. The trunk VSAN technology reduces the number of physical connections, actually implementing logical isolation in a physical network. Trunk VSAN in an FCoE network FCoE carries FC over Ethernet. In an FCoE network - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 54
1. Enter system view. 2. Create a VSAN and enter VSAN view. Command system-view vsan vsan-id Remarks N/A By default, only the default VSAN (VSAN 1) exists. Configuring a trunk VSAN A VFC interface can be assigned to multiple VSANs as a trunk port. If you assign an interface to VSANs as a trunk - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 55
diagram Configuration considerations ports, so that the link between the two FCF switches can send and receive the frames of the two VSANs at the same time. Configuration procedure 1. Configure Switch A: # Configure Switch A to operate in advanced mode, save the configuration, and reboot Switch - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 56
Ethernet frame header ACL numbered 4000, and configure two rules to match FCoE frames (protocol type 0x8906) and FIP frames (protocol type 0x8914). [SwitchA] acl number quit # Configure the mapping from 802.1p priority 3 to local precedence 3 in the outbound direction. (This is the default, and you - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 57
1/1/5 to VLAN 10 as a trunk port. [SwitchA] interface ten-gigabitethernet 1/1/5 [SwitchA-Ten-GigabitEthernet1/1/5] port link-type trunk [SwitchA-Ten-GigabitEthernet1/1/5] port trunk permit vlan 10 [SwitchA-Ten-GigabitEthernet1/1/5] quit # Create interface VFC 2, and configure it to operate in F mode - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 58
20 to VSAN 20. [SwitchA] vlan 20 [SwitchA-vlan20] fcoe enable vsan 20 [SwitchA-vlan20] quit 2. Configure Switch B in the same way Switch A is configured. (Details not shown.) Verifying the configurations 1. Verify the configurations on Switch A by displaying member interfaces of all VSANs. [SwitchA - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 59
The output on Switch B is the same as that on Switch A. 53 - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 60
to the FIB table, which guides packet forwarding. An FCF switch maintains one routing table and link layer protocols • Static routes-Routes manually configured by the administrator • FSPF routes- routing table, use the display fc routing-table command as follows: display fc routing-table - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 61
The cost of direct routes is 0. The costs of static routes and FSPF routes are configurable. • Interface-Specifies the interface through which a matching FC frame is to be forwarded out of the FCF switch. FIB table contents Each entry in the FIB table specifies which interface a packet destined for - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 62
routes might fail to be reachable, and the network is interrupted. In this case, you must manually modify the static routes. Static routes support equal-cost routes. When you configure multiple equal-cost static routes to the same destination but with different outgoing interfaces, equal-cost routes - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 63
respective neighbors. In this way, all switches in the fabric receive that LSR. 6. Local LSDB updating results in SPF calculation. The calculated shortest path tree list is updated to the FSPF routing table. Configuring static routes for FC Configuration restrictions and guidelines • The destination - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 64
procedure To configure a static FC route: Step Command 1. Enter system view. system-view 2. Enter VSAN view. vsan vsan-id 3. Configure a static FC fc route-static fcid { mask | mask-length } route. interface-type interface-number [ cost cost-value ] Remarks N/A N/A By default, no static - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 65
by LSDB updating. To configure the minimum LSR receiving interval: Step 1. Enter system view. 2. Enter VSAN view. 3. Configure the minimum LSR receiving interval. Command system-view vsan vsan-id fspf min-ls-arrival value Remarks N/A N/A The default setting is 1 second. Configuring the minimum - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 66
the VFC interface in a specified VSAN. Command system-view interface vfc interface-number fspf hello-interval value vsan vsan-id Remarks N/A N/A The default setting is 20 seconds. Configuring the dead interval for an interface After two switches establish a neighbor relationship, they send hello - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 67
the dead interval for the VFC interface in a specified VSAN. Command system-view interface vfc interface-number fspf dead-interval value vsan vsan-id Remarks N/A N/A The default setting is 80 seconds. Configuring the LSR retransmission interval for interfaces The LSR retransmission interval - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 68
default, FSPF GR is disabled. The default setting is 120 seconds. Configuring the GR helper Step 1. Enter system view. 2. Enable FSPF GR helper. Command system-view fspf graceful-restart helper Remarks N/A By default slot slot-number ] display fc exchange link verbose [ slot slot-number [ exid - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 69
and reboot the system to make it effective. # Configure Switch A to operate in FCF mode. Enable the fabric configuration function in VSAN 1. system-view [SwitchA] fcoe-mode fcf [SwitchA] vsan 1 [SwitchA-vsan1] domain configure enable # Configure the domain ID as 1. [SwitchA-vsan1] domain - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 70
and reboot the system to make it effective. # Configure Switch A to operate in FCF mode. Enable the fabric configuration function in VSAN 1. system-view [SwitchA] fcoe-mode fcf [SwitchA] vsan 1 [SwitchA-vsan1] domain configure enable # Configure the domain ID as 2. [SwitchB-vsan1] domain - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 71
port. [SwitchB-Vfc2] bind interface ten-gigabitethernet 1/1/6 [SwitchB-Vfc2] port trunk Configure Switch A to operate in FCF mode. Enable the fabric configuration function in VSAN 1. system-view [SwitchA] fcoe-mode fcf [SwitchA] vsan 1 [SwitchA-vsan1] domain configure enable # Configure - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 72
port trunk permit vlan 10 [SwitchC-Ten-GigabitEthernet1/1/6] quit # Enable FCoE for VLAN 10 and map VLAN 10 to VSAN 1. [SwitchC] vlan 10 [SwitchC-vlan10] fcoe enable vsan 1 [SwitchC-vlan10] quit # Configure Display the FC routing table in VSAN 1 on Switch B. [SwitchB] display fc routing-table vsan 1 - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 73
Vfc2 InLoop0 InLoop0 InLoop0 InLoop0 # On Switch A, use the fcping command to ping Switch C and check whether Switch C is reachable. [SwitchA] fcping Switch A can reach Switch C. FSPF configuration example Network requirements As shown in Figure 18, configure FSPF to enable the two FCF switches - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 74
Configure Switch A to operate in FCF mode. Enable the fabric configuration function in VSAN 2. system-view [SwitchA] fcoe-mode fcf [SwitchA] vsan 2 [SwitchA-vsan2] domain configure enable # Configure port. [SwitchA-Vfc1] bind interface ten-gigabitethernet 1/1/5 [SwitchA-Vfc1] port trunk - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 75
Configure Switch B to operate in FCF mode. Enable the fabric configuration function in VSAN 2. system-view [SwitchB] fcoe-mode fcf [SwitchB] vsan 2 [SwitchB-vsan2] domain configure enable # Configure port. [SwitchB-Vfc1] bind interface ten-gigabitethernet 1/1/5 [SwitchB-Vfc1] port trunk - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 76
0xfffffc/24 DIRECT 0 0xfffffd/24 DIRECT 0 Cost 265 0 0 0 0 Interface Vfc1 InLoop0 InLoop0 InLoop0 InLoop0 # On Switch A, use the fcping command to ping Switch B and check whether Switch B is reachable. [SwitchA] fcping fcid fffc02 vsan 2 FCPING fcid 0xfffc02: 128 data bytes, press CTRL_C to - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 77
Configuring FC zones Overview The VSAN technology divides a physical SAN into multiple VSANs, which are separated from one another, and provides more secure, reliable, and flexible services services. This creates data security risks. Zoning can solve the preceding problem The same N-Ports can form - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 78
each zone can have multiple zone members. • To facilitate configuration, zone membership configuration supports use of zone aliases. A zone alias is a set fabric-wide basis, you must specify the active zone set by using a command on a local device and distribute it to the entire fabric. When you - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 79
) • Update Fabric Configuration (UFC) • Release Change Authorization (RCA) These types of packets implement locking, data synchronization, submission, and unlocking processes, respectively. These processes make sure only one device distributes data as the manager switch when multiple users trigger - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 80
with zone database information, the managed switch determines whether the total number of zones, zone sets, and switch updates its local zone database. It replies with an ACC packet for a successful update and with an RJT packet for a failed update. 6. The manager switch notifies managed switches - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 81
locally configured merge type, while the merged switches merge all received data, regardless of the their merge types. • The pWWN is a preferred choice over FC addresses to identify zone members, because FC addresses might change at fabric merge and the merge result might not be as expected by users - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 82
with an ACC packet. Otherwise, it replies with an RJT packet. c. After receiving the ACC packet, Switch A sends an MR request containing its zone data to Switch B. d. After receiving the MR request, Switch B obtains the zone data and merges it with its local zone data. Then, it replies with an - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 83
, require all participating switches to be configured with complete merge. switches isolate their connecting link by bringing down the relevant ports in the VSAN, in addition to keeping their zone databases unchanged. Access control If a server wants to access a disk through the name service - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 84
N_Ports can be indirectly connected to the switch. To configure a zone alias: Step 1. Enter system view. Command system-view 2. Enter VSAN view. vsan . By default, no member exists in a zone alias. Configuring zones You can configure a maximum of 512 zones for all VSANs on a switch. You - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 85
zone. Command zone name zone-name member { fcid fcid | pwwn pwwn | zone-alias zone-alias-name } Remarks If the zone has been created, enter its view directly. By default, no member exists in a zone. Configuring zone sets You can configure a maximum of 128 zone sets for all VSANs on a switch. To - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 86
Step 2. Enter VSAN view. 3. Configure zone distribution and merge types as complete distribution and complete merge. Command vsan vsan-id zoneset distribute full Remarks N/A The default setting is incomplete distribution and incomplete merge. Activating a zone set and distributing it to the - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 87
one. They have the same name but different contents. To copy a zone alias, zone, and zone set: Step 1. Enter system view. 2. Enter VSAN view. Command system-view vsan vsan-id 3. Copy an existing zone alias to create a new zone zone-alias clone src-name dest-name alias. 4. Copy an existing - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 88
all Displaying and maintaining FC zones Execute display commands in any view. Task Command Display zone alias information. display zone-alias id ] FC zone configuration example Network requirements As shown in Figure 23, all nodes have registered with the switches. Access control is specified - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 89
DCBX on the connecting Ethernet interface. For information about configuring DCBX, see Layer 2-LAN Switching Configuration Guide. For information about configuring physical-to-VFC interface bindings and VLAN-to-VSAN mappings, see "Configuring a VFC interface" and "Enabling FCoE for a VLAN and - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 90
[SwitchA] fcoe-mode fcf [SwitchA] vsan 1 # Create a zone alias Alias1, and add pWWN 22 the entire fabric. [SwitchA-vsan1] zoneset activate name Zoneset1 Verifying the configurations All verification tasks are performed on Switch B. # Display zone set information for VSAN 1. display zoneset - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 91
zone-alias Alias1 fcid 0x020004 pwwn 22:33:44:55:66:77:88:99 zone name Zone3 fcid 0x010003 zone-alias Alias1 fcid 0x020004 pwwn 22:33:44:55:66:77:88:99 # Display information about Zone 2 in VSAN 1. display zone name Zone2 vsan 1 VSAN 1: zone name Zone2 fcid 0x010002 pwwn 11:22:33:44:55:66: - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 92
is forwarded to the core switch. Uplink interface and uplink An uplink interface, also known as an external interface, is the interface through which an NPV switch connects to the core switch. It can be a VFC interface, which must be configured to operate in NP mode. An uplink is a link from an NPV - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 93
Tasks at a glance Remarks (Required.) Configuring the switch to operate in NPV mode See "Configuration procedure" in "Configuring an FCoE mode." (Required.) Configuring uplink interfaces and downlink interfaces N/A (Optional.) Configuring downlink-to-uplink interface mappings N/A (Optional - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 94
to operate in F mode. Command system-view interface vfc interface-number fc mode f Remarks N/A This interface is connected to a node. By default, a VFC interface on an NPV switch operates in F mode. Configuring downlink-to-uplink interface mappings CAUTION: If an uplink interface mapped by - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 95
VSAN view. 3. Configure a downlink-to-uplink interface mapping. Command Remarks system-view N/A vsan vsan-id N/A npv traffic-map server-interface interface-type interface-number external-interface interface-type interface-number By default, no mapping is configured. Initiating a disruptive - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 96
dot1-tlv dcbx [SwitchA-Ten-GigabitEthernet1/1/6] quit # Create an Ethernet frame header ACL numbered 4000, and configure two rules to match FCoE frames (protocol type 0x8906) and FIP frames (protocol type 0x8914). [SwitchA] acl number 4000 [SwitchA-acl-ethernetframe-4000] rule permit type 8906 ffff - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 97
[SwitchA-Ten-GigabitEthernet1/1/6] qos apply policy plcy outbound [SwitchA-Ten-GigabitEthernet1/1/6] quit # Configure the mapping from 802.1p priority 3 to local precedence 3 in the outbound direction. (This is the default, and you can modify the mapping as needed.) [SwitchA] qos map-table dot1p - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 98
-type trunk [SwitchA-Ten-GigabitEthernet1/1/7] port trunk permit vlan 10 [SwitchA-Ten-GigabitEthernet1/1/7] quit # Enable FCoE for VLAN 10 and map VLAN 10 to VSAN 1. [SwitchA] vlan 10 [SwitchA-vlan10] fcoe enable vsan 1 [SwitchA-vlan10] quit # Configure the uplink interface. [SwitchA] interface vfc - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 99
SwitchB] vlan 10 [SwitchB-vlan10] fcoe enable vsan 1 [SwitchB-vlan10] quit Verifying the configurations # Display the nodes on downlink interfaces and their mapped uplink interfaces. [SwitchA] display npv login Server External Interface VSAN FCID Port WWN Node WWN Interface Vfc1 1 0x010001 - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 100
Interfaces: Interface: Vfc1 VSAN tagging mode: Tagging VSAN State 1 Up Interface: Vfc2 VSAN tagging mode: Tagging VSAN State 1 Up Number of Server Interfaces: 2 # Display the traffic mapping information. [SwitchA] display npv traffic-map NPV traffic map information of VSAN 1: Server - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 101
requests sent and the number of replies received, and it determines the distance between the source and destination based on the round-trip time of FC ping packets. A switch supports the following FC ping operations: • FC ping an N_Port from the switch-Use the fcping command on the switch to ping an - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 102
changed, please save the configuration and reboot the system to make it effective. # Configure Switch A to operate in FCF mode, and enable the fabric configuration function in VSAN 1 (optional, because this function is enabled by default). system-view [SwitchA] fcoe-mode fcf [SwitchA] vsan - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 103
changed, please save the configuration and reboot the system to make it effective. # Configure Switch B to operate in FCF mode, and enable the fabric configuration function in VSAN 1 (optional, because this function is enabled by default). system-view [SwitchB] fcoe-mode fcf [SwitchB] vsan - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 104
Reply from 0xfffc02: bytes = 128 time = 14 ms Reply from 0xfffc02: bytes = 128 time = 25 ms --- 0xfffc02 fcping statistics --5 packet(s) transmitted 5 packet(s) received 0.00% packet loss round-trip min/avg/max = 9/18/25 ms 98 - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 105
Configuring FC tracert Overview In an FC SAN, use the fctracert command to obtain bidirectional routing the destination switch. (If the destination of FC tracert is a node, the destination switch refers to the FCF switch directly connected to the node.) Each switch adds its uplink path information - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 106
process. b. After receiving the STR request packet with a downlink flag, Switch A outputs information about all uplink and downlink switches. Configuration procedure Task Command Detect bidirectional routing information between source and destination. fctracert [ -t timeout ] fcid fcid vsan - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 107
[SwitchA-Ten-GigabitEthernet1/1/5] port trunk permit vlan 10 [SwitchA-Ten-GigabitEthernet1/1/5] quit # Enable FCoE for VLAN 10 and map VLAN 10 to VSAN 1. [SwitchA] vlan 10 [SwitchA-vlan10] fcoe enable vsan 1 [SwitchA-vlan10] quit 2. Configure Switch B: # Configure Switch B to operate in advanced - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 108
[SwitchB-Ten-GigabitEthernet1/1/6] port trunk permit vlan 10 [SwitchB-Ten-GigabitEthernet1/1/6] quit # Enable FCoE for VLAN 10 and map VLAN 10 to VSAN 1. [SwitchB] vlan 10 [SwitchB-vlan10] fcoe enable vsan 1 [SwitchB-vlan10] quit 3. Configure Switch C: # Configure Switch C to operate in advanced - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 109
[SwitchC-Ten-GigabitEthernet1/1/6] port trunk permit vlan 10 [SwitchC-Ten-GigabitEthernet1/1/6] quit # Enable FCoE for VLAN 10 and map VLAN 10 to VSAN 1. [SwitchC] vlan 10 [SwitchC-vlan10] fcoe enable vsan 1 [SwitchC-vlan10] quit 4. On Switch A, use the fcping command to ping Switch C and check - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 110
:00:02:82(0xfffc01) 20:00:00:05:30:00:18:db(0xfffc02) Fctracert uncompleted: no route to destination port. The output shows that Switch A can reach Switch B, but Switch B cannot reach Switch C. Therefore, you can use the display fc routing-table command on Switch B to see whether there is a route to - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 111
of well-known fabric addresses FC_ID 0xFFFFF0 0xFFFFF1-0xFFFFF3 0xFFFFF4 0xFFFFF5 0xFFFFF6 0xFFFFF7 0xFFFFF8 Description N_Port controller, representing all N_Ports. Reserved. Event services. Multicast server. Clock synchronization services. Security key distribution services. Alias services. 105 - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 112
FC_ID 0xFFFFF9 0xFFFFFA 0xFFFFFB 0xFFFFFC Description Reserved. Management services. Time services. Path services (name services). 106 - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 113
Acronyms. Websites • HP.com http://www.hp.com • HP Networking http://www.hp.com/go/networking • HP manuals http://www.hp.com/support/manuals • HP download drivers and software http://www.hp.com/support/downloads • HP software depot http://www.software.hp.com • HP Education http://www.hp.com/learn - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 114
Command conventions Convention Boldface Italic [ ] { x | y | ... } [ x | y | ... ] { x | y | ... } * [ x | y | ... ] * & # Description Bold text represents commands bold text. For example, the New User window appears; click OK. Multi-level or damage to hardware or software. An alert that calls - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 115
wired-WLAN switch. Represents an access point. Represents a security product, such as a firewall, a UTM, or a load-balancing or security card that is installed in a device. Represents a security card, such as a firewall card, a load-balancing card, or a NetStream card. Port numbering in examples - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 116
build, 32 FCoE fabric switch domain IDs, 26 FCoE fabric VFC interface RCF request rejection, 29 FCoE FC default zone policy, 79 FCoE FC forwarding, 54 FCoE FC FSPF, 58 FCoE FC ping, 95, 95 FCoE FC routing, 54 FCoE FC static route, 57, 63 FCoE FC tracert, 99, 100 FCoE FC zone aliases, 78 FCoE FC zone - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 117
NPV load balancing, 87 distributing FCoE distributed service timeout timer, 27 FCoE FC zone set to fabric, 80 domain FCoE allowed domain ID listconfiguration, 26 FCoE fabric domain ID assignment, 22 FCoE fabric switch domain ID configuration, 26 downlink-to-uplink interface mapping FCoE, 88 NPV, 87 - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 118
, 63 FCoE FC tracert configuration, 99, 100 FCoE FC zone configuration, 71, 77, 82 FCoE frames, 6 FCoE FSPF configuration, 67 FCoE mode configuration, 11 FCoE NPV configuration, 86, 87, 89 FCoE overview, 1 FCoE VSAN configuration, 47, 48 FCoE well-known fabric addresses, 105 F fabric default FC4 - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 119
32 fabric switch domain ID configuration, 26 fabric switch priority setting, 25 fabric timer configuration, 27 fabric VFC interface RCF request rejection, 29 FC access control, 77 FC address, 2 FC default zone policy, 79 FC direct routes, 55 FC FIB table, 54 FC forwarding configuration, 54 FC frame - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 120
, 13, 17 VN interface, 6 VSAN, 4 VSAN configuration, 47, 48 VSAN creation, 48 VSAN fundamentals, 47 VSAN-VLAN mapping restrictions, 14 well-known fabric addresses, 105 WWN, 2 FIB FC FIB table, 54 FC routing table, 54 Fibre Channel over Ethernet. Use FCoE FIP how it works, 7 VFC interface/FIP - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 121
14 mode FCoE fabric dynamic build configuration, 37 FCoE fabric dynamic mode, 21 FCoE fabric static build configuration, 32 FCoE fabric static mode, 21 FCoE FCF, 8 FCoE feature support, 11 FCoE non-FCoE, 8 FCoE NPV, 8, 9 FCoE port modes, 3 FCoE switch mode configuration, 11 FCoE transit, 8 FCoE VFC - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 122
95, 95 policy FCoE FC default zone policy, 79 port FC direct routes, 55 FCoE FC zone database, 71 FCoE trunk VSAN, 47 FCoE trunk VSAN configuration, 48 FCoE trunk VSAN in FCoE network, 47 priority FCoE fabric switch priority setting, 25 FCoE FCF priority configuration, 16, 16 FCoE VFC interface FCF - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 123
FCoE fabric switch domain IDs, 26 configuring FCoE fabric VFC interface RCF request rejection, 29 configuring FCoE FC default zone policy, 79 configuring FCoE FC FSPF, 58 configuring FCoE FC ping, 95, 95 configuring FCoE FC static route, 57, 63 configuring FCoE FC tracert, 99, 100 configuring FCoE - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 124
87 FCoE NPV uplink, 86 FCoE NPV uplink interface, 86 FCoE overview, 1 FCoE trunk VSAN, 47 FCoE trunk VSAN in FCoE network, 47 FCoE trunk VSAN mode configuration, 48 FCoE VSAN, 4 FCoE VSAN configuration, 47, 48 FCoE VSAN creation, 48 FCoE WWN, 2 selecting FCoE fabric principal switch, 21 setting FCoE - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 125
FC routing table, 54 timer FCoE fabric distributed service timeout timer, 27 FCoE fabric error detection timeout timer, 27 FCoE fabric resource allocation timeout timer, 27 tracert FCoE FC tracert configuration, 99, 100 transit mode (FCoE), 8, 11 transmitting FC frames, 7 triggering FCoE FC zone set - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 126
FCoE fabric static building configuration, 32 FCoE FC zone, 4 FCoE for VLAN enable, 14 FCoE FSPF configuration, 67 FCoE mode configuration, 11 FCoE NPV configuration, 86, 87, 89 FCoE overview, 1 FCoE trunk VSAN configuration, 48 FCoE VSAN to VLAN mapping, 14 FCoE WWN, 2 fundamentals, 47 manual FCoE - HP 6125XLG | R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 127
FCoE FC zone distribution, 79 FCoE FC zone merge type, 79 FCoE FC zone set activation, 80 FCoE FC zone set configuration, 79 FCoE FC zone set distribution triggering, 80 FCoE FC zone set fabric distribution, 80 FCoE FC zone-related copying, 81 FCoE FC zone-related renaming, 81 121
HP 6125XLG Blade Switch
FCoE
Configuration Guide
Part number: 5998-3726
Software version: Release 2306
Document version: 6W100-20130912