HP 6125XLG R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 56
and con the action of marking packets with 802.1p, enable the interfaces to advertise DCBX TLVs.
View all HP 6125XLG manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 56 highlights
[SwitchA-vsan10] quit [SwitchA] vsan 20 [SwitchA-vsan20] quit # Enable LLDP globally. [SwitchA] lldp global enable # Enable LLDP on interfaces Ten-GigabitEthernet 1/1/5 and Ten-GigabitEthernet 1/1/6, and enable the interfaces to advertise DCBX TLVs. [SwitchA] interface ten-gigabitethernet 1/1/5 [SwitchA-Ten-GigabitEthernet1/1/5] lldp enable [SwitchA-Ten-GigabitEthernet1/1/5] lldp tlv-enable dot1-tlv dcbx [SwitchA-Ten-GigabitEthernet1/1/5] quit [SwitchA] interface ten-gigabitethernet 1/1/6 [SwitchA-Ten-GigabitEthernet1/1/6] lldp enable [SwitchA-Ten-GigabitEthernet1/1/6] lldp tlv-enable dot1-tlv dcbx [SwitchA-Ten-GigabitEthernet1/1/6] quit # Create an Ethernet frame header ACL numbered 4000, and configure two rules to match FCoE frames (protocol type 0x8906) and FIP frames (protocol type 0x8914). [SwitchA] acl number 4000 [SwitchA-acl-ethernetframe-4000] rule permit type 8906 ffff [SwitchA-acl-ethernetframe-4000] rule permit type 8914 ffff [SwitchA-acl-ethernetframe-4000] quit # Create a class named app_c with the logic OR operator, and specify ACL 4000 as the match criterion. [SwitchA] traffic classifier app_c operator or [SwitchA-classifier-app_c] if-match acl 4000 [SwitchA-classifier-app_c] quit # Create a behavior named app_b, and configure the action of marking packets with 802.1p priority 3. [SwitchA] traffic behavior app_b [SwitchA-behavior-app_b] remark dot1p 3 [SwitchA-behavior-app_b] quit # Create a QoS policy named plcy, and associate the class app_c with the behavior app_b in the QoS policy, specifying that the class-behavior association applies only to DCBX. [SwitchA] qos policy plcy [SwitchA-qospolicy-plcy] classifier app_c behavior app_b mode dcbx [SwitchA-qospolicy-plcy] quit # Apply the QoS policy plcy to the outbound direction of Ten-GigabitEthernet 1/1/5 and Ten-GigabitEthernet 1/1/6. [SwitchA] interface ten-gigabitethernet 1/1/5 [SwitchA-Ten-GigabitEthernet1/1/5] qos apply policy plcy outbound [SwitchA-Ten-GigabitEthernet1/1/5] quit [SwitchA] interface ten-gigabitethernet 1/1/6 [SwitchA-Ten-GigabitEthernet1/1/6] qos apply policy plcy outbound [SwitchA-Ten-GigabitEthernet1/1/6] quit # Configure the mapping from 802.1p priority 3 to local precedence 3 in the outbound direction. (This is the default, and you can modify the mapping as needed.) [SwitchA] qos map-table dot1p-lp 50