HP 6125XLG R2306-HP 6125XLG Blade Switch FCoE Configuration Guide - Page 55

Configuration considerations, Configuration procedure, Con Switch

Get HP 6125XLG PDF manuals and user guides View all HP 6125XLG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

• Server A can read and write only the data of Disk A and Disk B. • Server B can read and write only the data of Disk C. Figure 16 Network diagram Configuration considerations • To meet these requirements, divide the SAN into two VSANs, VSAN 10 and VSAN 20. Each VSAN contains a server and disk devices that can exchange data. • Configure the two interfaces connecting FCF switch Switch A to the servers to operate in F mode, and assign the two interfaces as trunk ports to VSAN 10 and VSAN 20, respectively. • Configure the three interfaces connecting FCF switch Switch B to the disk devices to operate in F mode, and assign the three interfaces as trunk ports to VSAN 10 or VSAN 20. • Configure the interfaces connecting Switch A and Switch B to operate in E mode, configure the trunk mode as on for the two interfaces, and assign the interfaces to VSANs 10 and 20 as trunk ports, so that the link between the two FCF switches can send and receive the frames of the two VSANs at the same time. Configuration procedure 1. Configure Switch A: # Configure Switch A to operate in advanced mode, save the configuration, and reboot Switch A. (Skip this step if the switch is operating in advanced mode.) system-view [SwitchA] system-working-mode advance Do you want to change the system working mode? [Y/N]:y The system working mode is changed, please save the configuration and reboot the system to make it effective. # Configure Switch A to operate in FCF mode. Create VSAN s 10 and 20. system-view [SwitchA] fcoe-mode fcf [SwitchA] vsan 10 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
49
•
Server A can read and write only the data of Disk A and Disk B.
•
Server B can read and write only the data of Disk C.
Figure 16
Network diagram
Configuration considerations
•
To meet these requirements, divide the SAN into two VSANs, VSAN 10 and VSAN 20. Each VSAN
contains a server and disk devices that can exchange data.
•
Configure the two interfaces connecting FCF switch Switch A to the servers to operate in F mode,
and assign the two interfaces as trunk ports to VSAN 10 and VSAN 20, respectively.
•
Configure the three interfaces connecting FCF switch Switch B to the disk devices to operate in F
mode, and assign the three interfaces as trunk ports to VSAN 10 or VSAN 20.
•
Configure the interfaces connecting Switch A and Switch B to operate in E mode, configure the
trunk mode as
on
for the two interfaces, and assign the interfaces to VSANs 10 and 20 as trunk
ports, so that the link between the two FCF switches can send and receive the frames of the two
VSANs at the same time.
Configuration procedure
1.
Configure Switch A:
# Configure Switch A to operate in advanced mode, save the configuration, and reboot Switch A.
(Skip this step if the switch is operating in advanced mode.)
<SwitchA> system-view
[SwitchA] system-working-mode advance
Do you want to change the system working mode? [Y/N]:y
The system working mode is changed, please save the configuration and reboot the
system to make it effective.
# Configure Switch A to operate in FCF mode. Create VSAN s 10 and 20.
<SwitchA> system-view
[SwitchA] fcoe-mode fcf
[SwitchA] vsan 10