HP LH4r HP Netserver LXr 8000 Installation Guide - Page 32

Removing Only the PCI Hot Plug Access Panel

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Chapter 3 Opening and Closing the HP NetServer Figure 3-3. Lifting Off the Cover 5. To replace the cover, lower it onto the top of the server, about a half-inch to the rear of its normal position when closed. See Figure 3-2. 6. Push the cover forward until the slots in its front edge line up with the screw holes on the server's chassis. 7. Reattach the screws. Removing Only the PCI Hot Plug Access Panel NOTE You can safely remove the access hatch to reach PCI Hot Plug boards while the server is operating. The server can operate safely with this hatch removed. CAUTION If you plan to remove a PCI Hot Plug board from one of these slots while the server is powered up, first power down the slot through your network operating system (NOS). See Chapter 6 for details before proceeding. If you attempt to physically remove the board without first shutting down power through the NOS, problems may occur. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
Chapter 3
Opening and Closing the HP NetServer
24
Figure 3-3. Lifting Off the Cover
5.
To replace the cover, lower it onto the top of the server, about a half-inch
to the rear of its normal position when closed. See Figure 3-2.
6.
Push the cover forward until the slots in its front edge line up with the
screw holes on the server’s chassis.
7.
Reattach the screws.
Removing Only the PCI Hot Plug Access Panel
NOTE
You can safely remove the access hatch to reach PCI Hot Plug
boards while the server is operating. The server can operate
safely with this hatch removed.
CAUTION
If you plan to remove a PCI Hot Plug board from one of these
slots while the server is powered up, first power down the slot
through your network operating system (NOS). See Chapter 6
for details before proceeding. If you attempt to physically
remove the board without first shutting down power through
the NOS, problems may occur.