HP LH4r HP Netserver LXr 8000 Installation Guide - Page 48

Removing and Replacing the Memory Board

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Chapter 5 Installing Additional Memory Figure 5-5. 24-DIMM and 32-DIMM Configuration for Interleaved Memory Boards Removing and Replacing the Memory Board To remove the memory board, follow this procedure: 1. Log off all users. Back-up files. Follow instructions in your network operating system (NOS) documentation to gracefully shut down all networking software and applications. 2. Press the power switch on the HP NetServer's control panel when prompted by the operating system. Normally, this is the complete procedure. NOTE The power supplies continue to provide standby current to the NetServer until the power cable is disconnected. 3. Disconnect the power cables and signal cables, and if necessary, label them to support reassembly. 4. Swing the front bezel open, or remove it entirely. See Chapter 3 for details. 5. On the front of the HP NetServer, locate the the LCD display. On top of the display's housing is a small handle. With one finger, pull up on this handle. The LCD display should move up about ½ inch and stop. See Figure 5-6. NOTE If you do not push the LCD display up and out of the way, you cannot remove the panel that covers the memory bays. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
Chapter 5
Installing Additional Memory
40
Figure 5-5. 24-DIMM and 32-DIMM Configuration for Interleaved Memory Boards
Removing and Replacing the Memory Board
To remove the memory board, follow this procedure:
1.
Log off all users. Back-up files. Follow instructions in your network
operating system (NOS) documentation to gracefully shut down all
networking software and applications.
2.
Press the power switch on the HP NetServer’s control panel when
prompted by the operating system. Normally, this is the complete
procedure.
NOTE
The power supplies continue to provide standby current to the
NetServer until the power cable is disconnected.
3.
Disconnect the power cables and signal cables, and if necessary, label
them to support reassembly.
4.
Swing the front bezel open, or remove it entirely. See Chapter 3 for
details.
5.
On the front of the HP NetServer, locate the the LCD display. On top of
the display’s housing is a small handle. With one finger, pull up on this
handle. The LCD display should move up about ½ inch and stop. See
Figure 5-6.
NOTE
If you do not push the LCD display up and out of the way, you
cannot remove the panel that covers the memory bays.