HP LH4r HP Netserver LXr 8000 Installation Guide - Page 34

rear of its normal position when closed. See

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Chapter 3 Opening and Closing the HP NetServer 2. Lift the access panel away from the top cover. See Figure 3-4. Shield blocks access slots that do not support PCI Hot Plug Figure 3-4. Lifting Off the Access Panel NOTE After you remove the access panel, a metal shield blocks your access to I/O slots P1 through P6, the slots that do not support PCI Hot Plug operation. To reach these slots, power down the server and remove the entire top cover. The shield then lifts off easily. 3. To replace the panel, lower it onto the top cover, about a half-inch to the rear of its normal position when closed. See Figure 3-3. 4. Push the cover forward until the slots in its front edge line up with the screw holes on the server's chassis. 5. Reattach the screws. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
Chapter 3
Opening and Closing the HP NetServer
26
2.
Lift the access panel away from the top cover. See Figure 3-4.
Shield blocks
access slots
that do not
support
PCI Hot Plug
Figure 3-4. Lifting Off the Access Panel
NOTE
After you remove the access panel, a metal shield blocks your
access to I/O slots P1 through P6, the slots that do not support
PCI Hot Plug operation. To reach these slots, power down the
server and remove the entire top cover. The shield then lifts
off easily.
3.
To replace the panel, lower it onto the top cover, about a half-inch to the
rear of its normal position when closed. See Figure 3-3.
4.
Push the cover forward until the slots in its front edge line up with the
screw holes on the server’s chassis.
5.
Reattach the screws.