HP LH4r HP Netserver LXr 8000 Installation Guide - Page 86

Step 1: Attaching Rack Nuts to the Rack

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

Chapter 8 Mounting the Server in the Rack HP NetServer Rack Mount Parts List Makes sure that the rack-mount kit that accompanies the HP NetServer contains the following parts: Table 8-1. Parts for Rack Mount Kit Quantity Description 2 Slides 12 Rack Nuts 12 Rack Nut Screws (M5 x 16mm) 8 Screws for Slides (8-32 x ¼ inch) 1 Template Step 1: Attaching Rack Nuts to the Rack CAUTION If other rack components are to be mounted in the rack below the HP NetServer, install those components before starting to mount the server. NOTE Use the HP Rack Assistant software to determine where in the rack to mount the HP NetServer. In this step, you attach rack nuts to the front and rear columns of the HP System/E or HP System/U rack. Some of these nuts will hold the server's slide in place. Others will fasten the front of the server to the rack. A cardboard rack-mounting template comes with the HP NetServer. This template shows you where to mount the nuts on the rack. 1. Find the rack-mounting template. If your HP NetServer is still in its box, the template should be in the accessories tray that sits on top of the server itself. 2. Hold the template alongside the outside face (the front) of one of the front rack columns. Line up the template with the same rack space that the server will occupy. (The template covers an area 7 EIA units high, the same height the server requires.) 78

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
Chapter 8
Mounting the Server in the Rack
78
HP NetServer Rack Mount Parts List
Makes sure that the rack-mount kit that accompanies the HP NetServer contains
the following parts:
Table 8-1. Parts for Rack Mount Kit
Quantity
Description
2
Slides
12
Rack Nuts
12
Rack Nut Screws (M5 x 16mm)
8
Screws for Slides (8-32 x ΒΌ inch)
1
Template
Step 1: Attaching Rack Nuts to the Rack
CAUTION
If other rack components are to be mounted in the rack below
the HP NetServer, install those components before starting to
mount the server.
NOTE
Use the HP Rack Assistant software to determine where in the
rack to mount the HP NetServer.
In this step, you attach rack nuts to the front and rear columns of the HP
System/E or HP System/U rack. Some of these nuts will hold the server's slide in
place. Others will fasten the front of the server to the rack.
A cardboard rack-mounting template comes with the HP NetServer. This
template shows you where to mount the nuts on the rack.
1.
Find the rack-mounting template. If your HP NetServer is still in its box,
the template should be in the accessories tray that sits on top of the server
itself.
2.
Hold the template alongside the outside face (the front) of one of the front
rack columns. Line up the template with the same rack space that the
server will occupy. (The template covers an area 7 EIA units high, the
same height the server requires.)