HP LH4r HP Netserver LXr 8000 Installation Guide - Page 94

Step 4: Attaching the Front Bezel

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

Chapter 8 Mounting the Server in the Rack Press in the release latch on each slide and push the server into the rack Flanges Figure 8-10. Pressing in the Release Latches 8. Each of the server's two front flanges has two slots. These slots should line up with rack nuts that you previously mounted on the rack columns. Insert screws through the flanges into the rack nuts, and fasten the server in place so it cannot slide. Step 4: Attaching the Front Bezel The front bezel is attached to the server by a hinge and a latch. You must attach the hinge and latch to the front of the server before mounting the bezel. 1. Push the hinge into place on the left edge of the front of the HP NetServer. The two hooks on the rear of the hinge must fit into the two matching holes on the front of the server. The hooks attach the hinge to the server, but not securely. See Figure 8-11. 86

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
Chapter 8
Mounting the Server in the Rack
86
Press in the release latch on
each slide and push the
server into the rack
Flanges
Figure 8-10. Pressing in the Release Latches
8.
Each of the server’s two front flanges has two slots. These slots should line
up with rack nuts that you previously mounted on the rack columns. Insert
screws through the flanges into the rack nuts, and fasten the server in
place so it cannot slide.
Step 4: Attaching the Front Bezel
The front bezel is attached to the server by a hinge and a latch. You must attach
the hinge and latch to the front of the server before mounting the bezel.
1.
Push the hinge into place on the left edge of the front of the HP NetServer.
The two hooks on the rear of the hinge must fit into the two matching
holes on the front of the server. The hooks attach the hinge to the server,
but not securely. See Figure 8-11.