HP LH4r HP Netserver LXr 8000 Installation Guide - Page 53

Memory Board.

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Chapter 5 Installing Additional Memory Figure 5-11. Installing a DIMM Module 5. Align the notches on the DIMM with the notches on the socket. 6. Hold the DIMM so that the front edge faces straight down into the connector (at a 90° angle to the memory board). 7. Insert the DIMM carefully into the desired slot. The retaining clips will grasp the DIMM automatically if it is inserted properly. CAUTION Do not rock the EDO DIMM into place, but apply firm and even pressure. If a gap exists between the retaining clips and the DIMM module, remove the module and repeat steps 5-7. 8. Repeat steps 3-7 to install DIMMs in the DIMM slot sequence listed in Figures 5-4 and 5-5 until you have installed all DIMMs for your memory configuration. 9. Replace the memory board in the server. See "Removing and Replacing a Memory Board." 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
Chapter 5
Installing Additional Memory
45
Figure 5-11. Installing a DIMM Module
5.
Align the notches on the DIMM with the notches on the socket.
6.
Hold the DIMM so that the front edge faces straight down into the
connector (at a 90
°
angle to the memory board).
7.
Insert the DIMM carefully into the desired slot. The retaining clips will
grasp the DIMM automatically if it is inserted properly.
CAUTION
Do not rock the EDO DIMM into place, but apply firm and
even pressure.
If a gap exists between the retaining clips and
the
DIMM module, remove the module and repeat steps 5-7.
8.
Repeat steps 3-7 to install DIMMs in the DIMM slot sequence listed in
Figures 5-4 and 5-5 until you have installed all DIMMs for your memory
configuration.
9.
Replace the memory board in the server. See "Removing and Replacing a
Memory Board."