HP LH4r HP Netserver LXr 8000 Installation Guide - Page 63

Removing a Hot Plug Board Bracket from a PCI Hot-Plug Slot

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Chapter 6 Installing Additional Boards 7. Consider the HP NetServer's boot order when selecting a slot on the I/O baseboard (Figure 6-1). If you are installing a SCSI controller board, the priority of the controllers (where the BIOS will search for the boot drive) is set by the board's slot location. Refer to "I/O Board Boot Order" earlier in this chapter. 8. When you have selected a slot, remove its slot cover on the server's rear panel. If you are installing a board in one of the PCI Hot Plug slots (P7 through P10), first remove the special Hot Plug board bracket from the inside of the server's rear panel. Then you can remove the slot cover. See Figure 6-3. Hot Plug Board Bracket (Loosen Captive Screw to Detach) Figure 6-3. Removing a Hot Plug Board Bracket from a PCI Hot-Plug Slot 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
Chapter 6
Installing Additional Boards
55
7.
Consider the HP NetServer’s boot order when selecting a slot on the I/O
baseboard (Figure 6-1). If you are installing a SCSI controller board, the
priority of the controllers (where the BIOS will search for the boot drive)
is set by the board’s slot location. Refer to "I/O Board Boot Order" earlier
in this chapter.
8.
When you have selected a slot, remove its slot cover on the server's rear
panel.
If you are installing a board in one of the PCI Hot Plug slots (P7 through
P10), first remove the special Hot Plug board bracket from the inside of
the server's rear panel. Then you can remove the slot cover. See Figure
6-3.
Hot Plug Board
Bracket (Loosen
Captive Screw
to Detach)
Figure 6-3. Removing a Hot Plug Board Bracket from a PCI Hot-Plug Slot