HP LH4r HP Netserver LXr 8000 Installation Guide - Page 51

See

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Chapter 5 Installing Additional Memory 11. To replace the memory board, hold it in front of its bay, with the component-side down. The end of the board with the connector must point into the memory board bay. 12. Slide the board into the guide rails on either side of the memory board bay. Push the board in until it seats in the slot at the rear of the bay. See Figure 5-8. Guide Rails Memory Board Figure 5-8. Replacing the Memory Board 13. Close the memory board's retaining latches. They should clamp onto the sides of the bay and hold the board firmly in place. 14. Reattach the memory access panel to the front of the HP NetServer chassis (Figure 5-6). 15. Push the LCD down into its original position ( Figure 5-6). 16. Reattach the front bezel. See Chapter 3 for details. 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
Chapter 5
Installing Additional Memory
43
11.
To replace the memory board, hold it in front of its bay, with the
component-side down. The end of the board with the connector must point
into the memory board bay.
12.
Slide the board into the guide rails on either side of the memory board
bay. Push the board in until it seats in the slot at the rear of the bay.
See Figure 5-8.
Guide
Rails
Memory
Board
Figure 5-8. Replacing the Memory Board
13.
Close the memory board’s retaining latches. They should clamp onto the
sides of the bay and hold the board firmly in place.
14.
Reattach the memory access panel to the front of the HP NetServer chassis
(Figure 5-6).
15.
Push the LCD down into its original position ( Figure 5-6).
16.
Reattach the front bezel. See Chapter 3 for details.