HP LH4r HP Netserver LXr 8000 Installation Guide - Page 90

Step 3: Placing the HP NetServer in the Rack

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

Chapter 8 Mounting the Server in the Rack Step 3: Placing the HP NetServer in the Rack WARNING If you have not done so already, pull the rack's stabilizing foot forward out of the bottom of the rack to prevent rack instability while mounting the HP NetServer. Failure to do so could result in injury and equipment damage. Figure 8-5 shows the stabilizing foot in position. 1. Before lifting the HP NetServer, remove all three power supply modules. Pull down the black handle on each module, then pull the module out of the server. See Figure 8-6. Figure 8-6. Removing the Power Supply Modules WARNING The HP NetServer weighs more than 130 pounds. Removing the power supplies reduces this weight significantly and reduces the likelihood of accidents. Reinstall the power supplies only after the server is securely mounted. At least two people must be on hand to lift the server into position. Failure to observer this warning could result in serious injury to you or damage to the HP NetServer. 82

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
Chapter 8
Mounting the Server in the Rack
82
Step 3: Placing the HP NetServer in the Rack
WARNING
If you have not done so already, pull the rack’s stabilizing
foot forward out of the bottom of the rack to prevent rack
instability while mounting the HP NetServer. Failure to do so
could result in injury and equipment damage. Figure 8-5
shows the stabilizing foot in position.
1.
Before lifting the HP NetServer, remove all three power supply modules.
Pull down the black handle on each module, then pull the module out of
the server. See Figure 8-6.
Figure 8-6. Removing the Power Supply Modules
WARNING
The HP NetServer weighs more than 130 pounds. Removing
the power supplies reduces this weight significantly and
reduces the likelihood of accidents. Reinstall the power
supplies only after the server is securely mounted. At least
two people must be on hand to lift the server into position.
Failure to observer this warning could result in serious injury
to you or damage to the HP NetServer.