HP Vectra VEi8 HP Vectra VEi7, Troubleshooting and Upgrade Guide - Page 33

HP Setup Program, Device Boot Order, Boot Menu for the Current Startup, First, Turn On or Restart

Get HP Vectra VEi8 PDF manuals and user guides View all HP Vectra VEi8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

1 Troubleshooting Your PC HP Setup Program HP Setup Program Follow these instructions to check your PC's configuration when you first use the PC: First, Turn On or Restart If your PC is off, turn on the display and then the PC. Your PC If the PC is already turned on, save your data, exit all programs and restart your PC. For Windows NT 4.0, Windows 95 or Windows 98, use the Shut Down Restart your computer command in the Start menu. This command will automatically exit the operating system and restart the PC. For operating systems such as Windows NT 3.51, you must exit the operating system, then manually switch off and then on the PC. To Go to the Setup Program To go immediately into the Setup program while the Hewlett-Packard logo appears on your display, press F2. The Setup program allows you to view and change the configuration of your PC, such as the passwords, standby (power saving) mode, IRQ settings and boot device order. Device Boot Order Boot Menu for the Current Startup NOTE You can only change the current startup boot device order on VEi 7 (Celeron-equipped) models. The current startup Boot menu gives the order of devices which the PC attempts to start or "boot" from (for example, the floppy drive first, the CD-ROM drive second, the hard disk drive third, and lastly the network). From this menu you can choose the device to boot from for the current startup. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
33
1
Troubleshooting Your PC
HP Setup Program
HP Setup Program
Follow these instructions to check your PC’s configuration when you
first use the PC:
First, Turn On or Restart
Your PC
If your PC is off, turn on the display and then the PC.
If the PC is already turned on, save your data, exit all programs and
restart your PC. For Windows NT 4.0, Windows 95 or Windows 98, use
the
Shut Down
±
Restart your computer
command in the
Start
menu. This
command will automatically exit the operating system and restart the
PC. For operating systems such as Windows NT 3.51, you must exit the
operating system, then manually switch off and then on the PC.
To Go to the Setup
Program
To go immediately into the
Setup
program while the
Hewlett-Packard
logo appears on your display, press
F2
.
The
Setup
program allows you to view and change the configuration of
your PC, such as the passwords, standby (power saving) mode, IRQ
settings and boot device order.
Device Boot Order
Boot Menu for the Current Startup
NOTE
You can only change the current startup boot device order on VEi 7
(Celeron-equipped) models.
The current startup
Boot
menu gives the order of devices which the PC
attempts to start or “boot” from (for example, the floppy drive first, the
CD-ROM drive second, the hard disk drive third, and lastly the
network). From this menu you can choose the device to boot from
for
the current startup
.