HP XM600 hp kayak xm600 series 1, user's guide for minitower models - Page 29

Removing the Memory Expansion Card and SDRAM Modules - kayak mother boards

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation Removing, Replacing and Upgrading Memory on Kayak XM600 models Removing the Memory Expansion Card and SDRAM Modules You cannot upgrade with RDRAM memory until the Memory Expansion Card and all SDRAM memory has been removed. 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover (refer to page 24 for detailed instructions). 3 Remove the HP UltraFlow Airflow Guide to obtain access to the SDRAM modules and sockets on the memory expansion card. 4 Release the retaining screw located on the Memory Expansion Card. Then remove the screw from the accessory card socket. 5 Open the two retaining clips on the system board to release the Memory Expansion Card, then remove it from the connector. 6 Remove the memory modules from the old Memory Expansion Card. To remove a memory module, open the two retaining clips and lift the module out of the socket. › › 7 Install the replacement RDRAM module(s) with the necessary Continuity and Terminator modules in the correct memory slots on the mother board, as described in the following section "Upgrading RDRAM Memory". 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
2
Installing and Replacing Hardware Parts in Your PC Workstation
Removing, Replacing and Upgrading Memory on Kayak XM600 models
29
Removing the Memory Expansion Card and SDRAM Modules
You cannot upgrade with RDRAM memory until the Memory Expansion
Card and all SDRAM memory has been removed.
1
Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2
Remove the PC Workstation’s cover (refer to page 24 for detailed
instructions).
3
Remove the HP UltraFlow Airflow Guide to obtain access to the SDRAM
modules and sockets on the memory expansion card.
4
Release the retaining screw located on the Memory Expansion Card.
Then remove the screw from the accessory card socket.
5
Open the two retaining clips on the system board to release the Memory
Expansion Card, then remove it from the connector.
6
Remove the memory modules from the old Memory Expansion Card. To
remove a memory module, open the two retaining clips and lift the
module out of the socket.
7
Install the replacement RDRAM module(s) with the necessary
Continuity and Terminator modules in the correct memory slots on the
mother board, as described in the following section “Upgrading RDRAM
Memory”.