HP XM600 hp kayak xm600 series 1, user's guide for minitower models - Page 39

HP Kayak XM600 Cables and Connectors

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation Installing Mass Storage Devices Before Installing an IDE Hard Disk • The ATA IDE cable supports two IDE devices. This cable is connected to the Primary IDE connector on the system board. The bootable hard disk drive is connected to this cable via the MASTER connector. A second hard disk drive could be installed by using the SLAVE connector. • A second IDE drive cable supports two IDE devices. If you install a CD-ROM drive, a DVD drive or a Zip drive, connect it to this cable. • The third cable has one connector for a floppy drive. Refer to the drive's installation guide to check jumper settings or if there is a special installation procedure to follow. HP Kayak XM600 Cables and Connectors Primary IDE cable supports two Hard Disk Drives Two IDE data cables each with two 40-pin connectors for IDE Drives Secondary IDE cable for access devices such as CD-ROM Drives or Zip Drives Primary IDE Connector Secondary IDE Connector Cable with one 34-pin connector for 3.5-inch Floppy Disk Drive Floppy Disk Drive Connector To identify the positions of other system board connectors, refer to the label located on the inside of the cover. 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
2
Installing and Replacing Hardware Parts in Your PC Workstation
Installing Mass Storage Devices
39
•
The ATA IDE cable supports two IDE devices. This cable is connected
to the Primary IDE connector on the system board. The bootable hard
disk drive is connected to this cable via the MASTER connector. A
second hard disk drive could be installed by using the SLAVE connector.
•
A second IDE drive cable supports two IDE devices. If you install a
CD-ROM drive, a DVD drive or a Zip drive, connect it to this cable.
•
The third cable has one connector for a floppy drive.
Before Installing an
IDE Hard Disk
Refer to the drive’s installation guide to check jumper settings or if there is
a special installation procedure to follow.
HP Kayak XM600 Cables and Connectors
Two IDE data cables each with
two 40-pin connectors for IDE
Drives
Cable with one 34-pin
connector for 3.5-inch Floppy
Disk Drive
Floppy Disk Drive Connector
Primary IDE Connector
Secondary IDE Connector
Primary IDE cable supports two
Hard Disk Drives
Secondary IDE cable for access
devices such as CD-ROM Drives
or Zip Drives
To identify the positions of other system board connectors, refer to the label located on
the inside of the cover.