HP XM600 hp kayak xm600 series 1, user's guide for minitower models - Page 34

Replacing the, Memory Expansion, Removing and Replacing a Memory Module

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation Removing, Replacing and Upgrading Memory on Kayak XU800 models 6 Remove the two retaining screws holding the Memory Expansion Card in place. 7 Open the two retaining clips on the Memory Expansion Card and remove it from the connector. Replacing the Memory Expansion Card 1 Install the Memory Expansion Card so that the memory modules face the processor. 2 Ensure the Memory Expansion Card is aligned with the guide rail on the fan and speaker assembly, and that the two notches on the Memory Expansion Card are aligned with those of the Memory Card Connector and accessory card panel. 3 With the two retaining clips open, press the Memory Expansion Card completely into the two connectors on the system board until the retaining clips click into position. Secure the Memory Expansion Card in place with the two retaining screws. 4 Replace the retaining bar and secure it in place with the screw. 5 Return the PC Workstation to its upright position. 6 Replace the HP Ultraflow Airflow Guide (see page 25). 7 Replace the PC workstation's cover (refer to page 24). Reconnect the power and telecommunications cables. Removing and Replacing a Memory Module NOTE Use only the HP memory modules provided for your PC model. The use of memory modules from any previous PC computers is not supported. If you want to find out about available accessories for your PC, refer to the HP Accessories Web site at: http://www.hp.com/go/pcaccessories 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN telecommunications cables. 2 Remove the PC workstation's cover (refer to page 23). 3 Remove the HP Ultraflow Airflow Guide (refer to page 25). 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
2
Installing and Replacing Hardware Parts in Your PC Workstation
Removing, Replacing and Upgrading Memory on Kayak XU800 models
34
6
Remove the two retaining screws holding the Memory Expansion Card
in place.
7
Open the two retaining clips on the Memory Expansion Card and remove
it from the connector.
Replacing the
Memory Expansion
Card
1
Install the Memory Expansion Card so that the memory modules face the
processor.
2
Ensure the Memory Expansion Card is aligned with the guide rail on the
fan and speaker assembly, and that the two notches on the Memory
Expansion Card are aligned with those of the Memory Card Connector
and accessory card panel.
3
With the two retaining clips open, press the Memory Expansion Card
completely into the two connectors on the system board until the
retaining clips click into position. Secure the Memory Expansion Card in
place with the two retaining screws.
4
Replace the retaining bar and secure it in place with the screw.
5
Return the PC Workstation to its upright position.
6
Replace the HP Ultraflow Airflow Guide (see page 25).
7
Replace the PC workstation’s cover (refer to page 24). Reconnect the
power and telecommunications cables.
Removing and Replacing a Memory Module
NOTE
Use only the HP memory modules provided for your PC model. The use of
memory modules from any previous PC computers is not supported. If you
want to find out about available accessories for your PC, refer to the HP
Accessories Web site at:
1
Switch off the display and PC Workstation. Disconnect all power cables
and any LAN telecommunications cables.
2
Remove the PC workstation’s cover (refer to page 23).
3
Remove the HP Ultraflow Airflow Guide (refer to page 25).