HP XM600 hp kayak xm600 series 1, user's guide for minitower models - Page 56

Replacing the Fan and Speaker Assembly, Removing the Fan, and Speaker, Assembly

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation Replacing the Fan and Speaker Assembly Removing the Fan and Speaker Assembly Replacing the Fan and Speaker Assembly 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover and front upper and lower bezels. Refer to page 23 for these instructions. 3 Disconnect the cables from their connectors located on the system board. 4 For ease of installation, place the PC Workstation on its side with the system board facing upwards. 5 Remove the PC chassis retaining bar. 6 For Kayak XU800 PC Workstations, remove the Memory Expansion Card. If required, refer to page 33 for instructions. 7 Remove the screw from the front of the chassis. 8 Unclip the three clips on the front of the chassis. 9 Slide the fan and speaker assembly towards the rear of the PC until it is clear of the chassis, then remove it from the PC Workstation. —  ž œ 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
2
Installing and Replacing Hardware Parts in Your PC Workstation
Replacing the Fan and Speaker Assembly
56
Replacing the Fan and Speaker Assembly
Removing the Fan
and Speaker
Assembly
1
Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2
Remove the PC Workstation’s cover and front upper and lower bezels.
Refer to page 23 for these instructions.
3
Disconnect the cables from their connectors located on the system
board.
4
For ease of installation, place the PC Workstation on its side with the
system board facing upwards.
5
Remove the PC chassis retaining bar.
6
For Kayak XU800 PC Workstations, remove the Memory Expansion
Card. If required, refer to page 33 for instructions.
7
Remove the screw from the front of the chassis.
8
Unclip the three clips on the front of the chassis.
9
Slide the fan and speaker assembly towards the rear of the PC until it is
clear of the chassis, then remove it from the PC Workstation.