HP XM600 hp kayak xm600 series 1, user's guide for minitower models - Page 47

Replacing the CD-ROM Drive (or DVD-Drive), Removing the, Old Drive, Installing the, New Drive

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation Replacing the CD-ROM Drive (or DVD-Drive) Removing the Old Drive Replacing the CD-ROM Drive (or DVD-Drive) 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover and front upper bezel (refer to page 23 for instructions). 3 Disconnect the power and data cables from the old drive. 4 Place one hand at the rear of the drive. 5 To release the drive, press the two locking clips located at the front of the drive inwards. From the back of the drive gently push forward to remove it from the shelf. 6 Remove the two long green guide rails by gently prying them off the drive. These guide rails will be required for the new drive. ê š Installing the New Drive 1 Add the guide rails to the new drive. The guide rails are inserted in the two holes located at the bottom of the drive. There is no specific side to which these guides must be installed. 2 Align the guide rails on both sides of the drive with the internal shelf guides, then slide the drive until it clicks into position. 3 Connect the power cable and the data cable to the rear of the new drive. The connectors are shaped to go in one way only. If you are not sure which connector to use, refer to "Installing Mass Storage Devices", on page 38. 4 Replace the front upper bezel and PC Workstation's cover (refer to page 24). Reconnect all the power and telecommunications cables. 5 Turn to page 49 to complete the installation. 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
2
Installing and Replacing Hardware Parts in Your PC Workstation
Replacing the CD-ROM Drive (or DVD-Drive)
47
Replacing the CD-ROM Drive (or DVD-Drive)
Removing the
Old Drive
1
Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2
Remove the PC Workstation’s cover and front upper bezel (refer to page
23 for instructions).
3
Disconnect the power and data cables from the old drive.
4
Place one hand at the rear of the drive.
5
To release the drive, press the two locking clips located at the front of
the drive inwards. From the back of the drive gently push forward to
remove it from the shelf.
6
Remove the two long green guide rails by gently prying them off the
drive. These guide rails will be required for the new drive.
Installing the
New Drive
1
Add the guide rails to the new drive. The guide rails are inserted in the
two holes located at the bottom of the drive. There is no specific side to
which these guides must be installed.
2
Align the guide rails on both sides of the drive with the internal shelf
guides, then slide the drive until it clicks into position.
3
Connect the power cable and the data cable to the rear of the new drive.
The connectors are shaped to go in one way only
. If you are not sure
which connector to use, refer to "Installing Mass Storage Devices", on
page 38.
4
Replace the front upper bezel and PC Workstation’s cover (refer to page
24). Reconnect all the power and telecommunications cables.
5
Turn to page 49 to complete the installation.
Œ