HP XM600 hp kayak xm600 series 1, user's guide for minitower models - Page 54

Replacing the Rear Fan, Removing the, Rear Fan

Get HP XM600 - Kayak - 128 MB RAM PDF manuals and user guides View all HP XM600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

2 Installing and Replacing Hardware Parts in Your PC Workstation Replacing the Rear Fan Removing the Rear Fan Replacing the Rear Fan 1 Switch off the display and PC Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2 Remove the PC Workstation's cover (refer to page 23 for instructions). 3 Remove the HP UltraFlow Airflow Guide (refer to page 25). 4 From the rear of the PC, holding the rear fan with one hand, use a screwdriver with the other hand to gently push one of the two retaining clips (direction of the stamped arrows on the chassis) inwards. Repeat this procedure with the second retaining clip. 5 Slide the rear fan towards the open space and remove from the chassis. ™ ™ š ™ 6 Disconnect the rear fan cable from the connector on the system board. If required, refer to the connector layout label located on the inside of the cover for the rear fan's position on the system board. 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
2
Installing and Replacing Hardware Parts in Your PC Workstation
Replacing the Rear Fan
54
Replacing the Rear Fan
Removing the
Rear Fan
1
Switch off the display and PC Workstation. Disconnect all power cables
and any LAN or telecommunications cables.
2
Remove the PC Workstation’s cover (refer to page 23 for instructions).
3
Remove the HP UltraFlow Airflow Guide (refer to page 25).
4
From the rear of the PC, holding the rear fan with one hand, use a
screwdriver with the other hand to gently push one of the two retaining
clips (direction of the stamped arrows on the chassis) inwards. Repeat
this procedure with the second retaining clip.
5
Slide the rear fan towards the open space and remove from the chassis.
6
Disconnect the rear fan cable from the connector on the system board.
If required, refer to the connector layout label located on the inside of
the cover for the rear fan’s position on the system board.