IBM 9228 Service Guide - Page 67

Removing a drive in bay 1

Get IBM 9228 - IntelliStation Z - Pro PDF manuals and user guides
UPC - 000435947840
View all IBM 9228 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Removing a drive in bay 1, 2, or 3 To remove a drive in bay 1, 2, or 3 complete the following steps. Release buttons Drive retainer clip Figure 25. Removing a drive from bay 1, 2, or 3 1. Read the safety information that begins on page vii and "Installation guidelines" on page 29. 2. Turn off the computer and all attached devices; then, disconnect all external cables and power cords. 3. Remove the side cover (see "Removing the side cover" on page 31). 4. Remove the two-piece bezel (see "Removing the two-piece bezel" on page 33). 5. Disconnect the power and signal cables from the drive that you are removing. 6. To remove a drive from bay 1 or 2, release the drive from the bay by pressing the blue release button on the side of the bay (see Figure 25). Pull the drive out of the computer. 7. To remove a diskette drive from bay 3, press the blue release button on the side of the bay. Pull the drive out of the front of the computer. 8. Remove the drive retainer clip from the side of the drive. Save the clip to use when you install the replacement drive. 9. If you are instructed to return the drive, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Chapter 4. Removing and replacing computer components 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
Removing a drive in bay 1, 2, or 3
To remove a drive in bay 1, 2, or 3 complete the following steps.
1.
Read the safety information that begins on page vii and “Installation guidelines”
on page 29.
2.
Turn off the computer and all attached devices; then, disconnect all external
cables and power cords.
3.
Remove the side cover (see “Removing the side cover” on page 31).
4.
Remove the two-piece bezel (see “Removing the two-piece bezel” on page 33).
5.
Disconnect the power and signal cables from the drive that you are removing.
6.
To remove a drive from bay 1 or 2, release the drive from the bay by pressing
the blue release button on the side of the bay (see Figure 25). Pull the drive out
of the computer.
7.
To remove a diskette drive from bay 3, press the blue release button on the side
of the bay. Pull the drive out of the front of the computer.
8.
Remove the drive retainer clip from the side of the drive. Save the clip to use
when you install the replacement drive.
9.
If you are instructed to return the drive, follow all packaging instructions, and
use any packaging materials for shipping that are supplied to you.
Drive retainer
clip
Release
buttons
Figure 25. Removing a drive from bay 1, 2, or 3
Chapter 4. Removing and replacing computer components
49