IBM 9228 Service Guide - Page 70

Installing a simple-swap drive in bay 4

Get IBM 9228 - IntelliStation Z - Pro PDF manuals and user guides
UPC - 000435947840
View all IBM 9228 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

To remove a simple-swap drive in bay 4, 5, 6, or 7 complete the following steps. Figure 27. Removing a simple-swap hard disk drive 1. Read the safety information that begins on page vii and "Installation guidelines" on page 29. 2. Turn off the computer and all attached devices; then, disconnect all external cables and power cords. 3. Unlock the side cover. The bezel will not disengage from the computer if the cover is locked. You do not have to remove the side cover. 4. Remove the lower bezel (see "Removing the two-piece bezel" on page 33). 5. Pull the loops of the drive assembly that is to be removed toward each other; then, pull the assembly out of the bay. 6. If you are instructed to return the drive, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing a simple-swap drive in bay 4, 5, 6, or 7 This procedure applies to a computer that has simple-swap hard disk drives. Some models come with simple-swap SATA or SAS hard disk drives, which are accessible from the front of the computer. Before you install a simple-swap SATA or SAS hard disk drive, read the following information: v Read the documentation that comes with the hard disk drive for cabling instructions. v You can install four simple-swap SATA or SAS hard disk drives in the computer. Drives are installed starting in bay 4. Additional drives are then installed in bays 5, 6, and 7. To install a simple-swap hard disk drive, complete the following steps. 52 IBM IntelliStation Z Pro Type 9228 and 9232: Problem Determination and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
To remove a simple-swap drive in bay 4, 5, 6, or 7 complete the following steps.
1.
Read the safety information that begins on page vii and “Installation guidelines”
on page 29.
2.
Turn off the computer and all attached devices; then, disconnect all external
cables and power cords.
3.
Unlock the side cover. The bezel will not disengage from the computer if the
cover is locked. You do not have to remove the side cover.
4.
Remove the lower bezel (see “Removing the two-piece bezel” on page 33).
5.
Pull the loops of the drive assembly that is to be removed toward each other;
then, pull the assembly out of the bay.
6.
If you are instructed to return the drive, follow all packaging instructions, and
use any packaging materials for shipping that are supplied to you.
Installing a simple-swap drive in bay 4, 5, 6, or 7
This procedure applies to a computer that has simple-swap hard disk drives.
Some models come with simple-swap SATA or SAS hard disk drives, which are
accessible from the front of the computer. Before you install a simple-swap SATA or
SAS hard disk drive, read the following information:
v
Read the documentation that comes with the hard disk drive for cabling
instructions.
v
You can install four simple-swap SATAor SAS hard disk drives in the computer.
Drives are installed starting in bay 4. Additional drives are then installed in bays
5, 6, and 7.
To install a simple-swap hard disk drive, complete the following steps.
Figure 27. Removing a simple-swap hard disk drive
52
IBM IntelliStation Z Pro Type 9228 and 9232: Problem Determination and Service Guide