IBM 9228 Service Guide - Page 72

Removing the hard disk drive fan

Get IBM 9228 - IntelliStation Z - Pro PDF manuals and user guides
UPC - 000435947840
View all IBM 9228 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Removing the hard disk drive fan Attention: v Replace a failed fan within 48 hours. v To ensure proper cooling and airflow, do not operate the computer for more than 30 minutes with the side cover removed. To remove the hard disk drive fan assembly, complete the following steps. Retaining tab Retaining latch Hard disk drive fan assembly Drive-cage release lever Figure 29. Removing the hard disk drive fan assembly 1. Read the safety information that begins on page vii and "Installation guidelines" on page 29. 2. Turn off the computer and all attached devices; then, disconnect all external cables and power cords. 3. Remove the side cover (see "Removing the side cover" on page 31). 4. Lift the power-supply handle and rotate the power supply out of the chassis. 5. Press and hold the drive-cage release lever; then, rotate the drive cage completely out of the chassis until the retaining tab on top of the cage locks into place. 6. Disconnect the hard disk drive fan cable from the system board, and note the location of the connector (see "System board internal connectors" on page 9). 7. Pull up on the fan-assembly retainer tabs at the blue press points; then, lift the assembly away from the drive cage. 8. Set the fan assembly on a level work surface with the fan facing up (see Figure 30 on page 55). 54 IBM IntelliStation Z Pro Type 9228 and 9232: Problem Determination and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
Removing the hard disk drive fan
Attention:
v
Replace a failed fan within 48 hours.
v
To ensure proper cooling and airflow, do not operate the computer for more than
30 minutes with the side cover removed.
To remove the hard disk drive fan assembly, complete the following steps.
Retaining tab
Drive-cage
release lever
Retaining
latch
Hard disk drive
fan assembly
1.
Read the safety information that begins on page vii and “Installation guidelines”
on page 29.
2.
Turn off the computer and all attached devices; then, disconnect all external
cables and power cords.
3.
Remove the side cover (see “Removing the side cover” on page 31).
4.
Lift the power-supply handle and rotate the power supply out of the chassis.
5.
Press and hold the drive-cage release lever; then, rotate the drive cage
completely out of the chassis until the retaining tab on top of the cage locks
into place.
6.
Disconnect the hard disk drive fan cable from the system board, and note the
location of the connector (see “System board internal connectors” on page 9).
7.
Pull up on the fan-assembly retainer tabs at the blue press points; then, lift the
assembly away from the drive cage.
8.
Set the fan assembly on a level work surface with the fan facing up (see
Figure 30 on page 55).
Figure 29. Removing the hard disk drive fan assembly
54
IBM IntelliStation Z Pro Type 9228 and 9232: Problem Determination and Service Guide