Kyocera KM-2030 2030 Instruction Handbook Rev 2C - Page 61

Message, Action, handbook and replace the staple cartridge.

Get Kyocera KM-2030 PDF manuals and user guides View all Kyocera KM-2030 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Message "Time for maintenance" CHAPTER 8 WHEN A PROBLEM OCCURS Action Periodic maintenance is necessary to keep your copier in good condition. Contact your service representative as soon as possible. Page "Memory is full." "Paper misfeed." "Reset all originals in feeder." "Misfeed in feeder. Remove original(s)." "Duplex tray inoperable, call for service." The copier memory is full. Select whether to print scanned pages (Print) or delete scanned data (Memory is full). You cannot copy or scan other originals until you make a selection. If paper is misfed, the copier will stop and the location of the misfeed will appear on the message display. Remove the misfed paper with the main switch turned ON (|) by following the appropriate procedure. 8-3 Originals have not been fed correctly from the DF (optional). Remove the originals with the main switch turned ON (|) by following the appropriate procedure. 8-6 The duplex unit (optional) is out of order and duplex copying is not possible. Contact your service representative immediately. "Paper capacity exceeded." "Remove paper from Inner." • There are 250 sheets of paper stored in the copy store section. Remove the paper and resume copying. • If the optional job separator is installed, there are 150 sheets of paper stored in the copy store section. Remove the paper and resume copying. 4-3 • If the optional finisher is installed, there are 100 sheets of paper stored in the 7-3 copy store section. Remove the paper and resume copying. "Paper capacity exceeded." "Remove paper from Finisher." There are 250 sheets of paper stored in the optional finisher. Remove the paper and resume copying. 7-3 "Paper capacity exeeded. Remove paper from Job sep." There are 100 sheets of paper stored on the optional job separator. Remove the paper and resume copying. 7-3 "Check paper in Finisher. Incomplete copies inside." Unfinished copies were ejected onto the finisher (optional) due to a problem occurred during copying. Check and remove those copies. "Remove paper from Finisher inner tray." Paper has been misfed inside the finisher (optional). See the finisher's instruction handbook and remove the paper. "Out of staples. Add staples." There are no staples in the finisher (optional). See the finisher's instruction handbook and replace the staple cartridge. "Cannot staple this size." Stapling is not possible with small size paper. For details, see the finisher's instruction handbook. 8-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
CHAPTER 8
WHEN A PROBLEM OCCURS
8-2
8-3
8-6
"Time for maintenance"
Periodic maintenance is necessary to keep your copier in good condition.
Contact your service representative as soon as possible.
"Memory is full."
The copier memory is full. Select whether to print scanned pages (Print) or
delete scanned data (Memory is full). You cannot copy or scan other originals
until you make a selection.
"Paper misfeed."
If paper is misfed, the copier will stop and the location of the misfeed will
appear on the message display. Remove the misfed paper with the main switch
turned ON (|) by following the appropriate procedure.
"Reset all originals in feeder."
"Misfeed in feeder. Remove original(s)."
Originals have not been fed correctly from the DF (optional). Remove the
originals with the main switch turned ON (|) by following the appropriate
procedure.
"Duplex tray inoperable, call for service."
The duplex unit (optional) is out of order and duplex copying is not possible.
Contact your service representative immediately.
Message
Action
Page
"Paper capacity exeeded.
Remove paper from Job sep."
There are 100 sheets of paper stored on the optional job separator. Remove
the paper and resume copying.
Paper has been misfed inside the finisher (optional). See the finisher's
instruction handbook and remove the paper.
There are no staples in the finisher (optional). See the finisher's instruction
handbook and replace the staple cartridge.
7-3
"Check paper in Finisher. Incomplete copies
inside."
Unfinished copies were ejected onto the finisher (optional) due to a problem
occurred during copying. Check and remove those copies.
"Remove paper from Finisher inner tray."
"Out of staples. Add staples."
"Cannot staple this size."
Stapling is not possible with small size paper. For details, see the finisher's
instruction handbook.
"Paper capacity exceeded."
"Remove paper from Inner."
4-3
7-3
• There are 250 sheets of paper stored in the copy store section. Remove the
paper and resume copying.
• If the optional job separator is installed, there are 150 sheets of paper stored
in the copy store section. Remove the paper and resume copying.
• If the optional finisher is installed, there are 100 sheets of paper stored in the
copy store section. Remove the paper and resume copying.
"Paper capacity exceeded."
"Remove paper from Finisher."
There are 250 sheets of paper stored in the optional finisher. Remove the
paper and resume copying.
7-3