Netgear DG834G DG834Gv5 Reference Manual - Page 117

Using Auto Policy to Con VPN Tunnels

Get Netgear DG834G - 54 Mbps Wireless ADSL Firewall Router PDF manuals and user guides
UPC - 606449029918
View all Netgear DG834G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 117 highlights

Wireless ADSL2+ Modem Router DG834G User Manual 6. Click Done on the Summary screen (see Figure 6-24) to complete the configuration procedure. The VPN Policies screen displays, showing that the new tunnel is enabled. Figure 6-26 Note: See "Using Auto Policy to Configure VPN Tunnels" on page 6-32 for information about how to enable the IKE keepalive capability on an existing VPN tunnel. 7. Repeat these steps for the DG834Gv5 on LAN B, and pay special attention to using the following network settings: • WAN IP of the remote VPN gateway (for example, 14.15.16.17) • LAN IP settings of the remote VPN gateway: - IP Address (for example, 192.168.0.1) - Subnet Mask (for example, 255.255.255.0) - Preshared Key (for example, 12345678) 8. Use the VPN Status screen to activate the VPN tunnel by performing the following steps: Note: The VPN Status screen is only one of three ways to active a VPN tunnel. See "Activating a VPN Tunnel" on page 6-25 for information about the other ways. Virtual Private Networking v1.0, May 2008 6-23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
Wireless ADSL2+ Modem Router DG834G User Manual
Virtual Private Networking
6-23
v1.0, May 2008
6.
Click
Done
on the Summary screen (see
Figure 6-24
) to complete the configuration
procedure. The VPN Policies screen displays, showing that the new tunnel is enabled.
7.
Repeat these steps for the DG834Gv5 on LAN B, and pay special attention to using the
following network settings:
•
WAN IP of the remote VPN gateway (for example,
14.15.16.17
)
•
LAN IP settings of the remote VPN gateway:
–
IP Address (for example,
192.168.0.1
)
–
Subnet Mask (for example,
255.255.255.0
)
–
Preshared Key (for example,
12345678
)
8.
Use the VPN Status screen to activate the VPN tunnel by performing the following steps:
Figure 6-26
Note:
See
“Using Auto Policy to Configure VPN Tunnels” on page 6-32
for
information about how to enable the IKE keepalive capability on an existing
VPN tunnel.
Note:
The VPN Status screen is only one of three ways to active a VPN tunnel. See
“Activating a VPN Tunnel” on page 6-25
for information about the other ways.