Home » Oki Manuals » Printers » Oki OKIPOS408II » Manual Viewer

Oki OKIPOS408II OKIPOS 408II Programmer s Technical Reference - Page 144

Two-Dimensional Bar Code QR Code Command Details, Print Bar code

Get Oki OKIPOS408II PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 144 highlights

3.13. Two-Dimensional Bar Code QR Code Command Details * Note that QR code is a registered trademark of DENSO WEB. This command is for printing 2-dimensional bar code QR codes. There are four functions of the commands relating to the 2-dimensional bar code QR codes, shown below. (1) Set bar code type (2) Set bar code data (3) Set page mode (4) Print Bar code (5) Set bar code type ( "y" "S") ( "y" "D") (Reserved) ( "y" "P") ( "y" "I") The details of each function are described below. (1) Set bar code type These commands set the bar code type. Because all initial values are set, use these only to make changes. (See the details for each setting below.) Cell Alignment Pattern "y" "S" "0" Sets the model Currently supported models are model 1 and model 2. Model 2 has a configuration including an alignment bar to improve its support of weight to handle skewing when codes are large. "y" "S" "1" Sets the error correction level QR codes can be read even if a part of the data is corrupted, by using error correction. Raising this level increases the size of the bar code because there is an increase in preparatory information. "y" "S" "2" Specifies the size of the cell (One four squared region configuring the QR code) The QR code is formed into a square of an equivalent size in the vertical and horizontal directions, but the size of the bar code image that is generated depends on the cell size setting. See Appendix 7 for details on the actual printed size of the QR code. These settings are individual settings. Therefore, even though there may not be any particular problem in each of them, there is the potential for an error to be generated. (See the descriptions below.) In such cases, the bar code will not be generated and the (4) Print command ( "y" "P") is ignored. With the (5) Get bar code expansion information command, an error code is returned. • Error is generated when generating a bar code by the combination of each setting command. • Print data exceeds the currently set print region Therefore, it is recommended to use (5) Get bar code expansion information command ( "y" "I") as a means for checking for these errors prior to printing. STAR Line Mode Command Specifications 3-126

Section	Page
1. INTERFACE CONFIGURATION	5
1.1. RS-232 Serial Interface	5
1.1.1. Specifications (Conforming to RS-232)	5
1.1.2. Signal array and explanations according to interface connector pin	5
1.1.3. Communication Protocol	6
1.2. Parallel Interfaces (Amphenol 36 pins)	8
1.2.1. Specifications (Conforming to IEEE1284)	8
1.2.2. Signal array and explanations according to interface connector pin	8
1.2.3. Signal Output Timing	9
1.2.4. Status Specification	9
1.3. USB Interface	10
1.4. Ethernet Interface	10
1.5. Wireless LAN Interface	10
1.6. Powered USB Interface	10
2. COMMAND FUNCTION LIST	11
3. COMMAND DETAILS	19
3.1. Explanation of Terms	19
3.2. Exception Processing	20
3.3. Standard Command Details	21
3.3.1. Font style and Character Set	21
ESC RS F n	21
ESC GS t n	22
ESC GS = n1 n2 da1 da2...dak db1 db2...dbk	23
ESC R n	25
ESC / n	26
ESC SP n	27
ESC M	28
ESC P	28
ESC :	28
ESC g	29
3.3.2. Character Expansion Settings	30
ESC i n1 n2	30
ESC W n	31
ESC h n	31
SO	32
DC4	32
ESC SO	33
ESC DC4	33
3.3.3. Print Mode	34
ESC E	34
ESC F	34
ESC – n	35
ESC _ n	35
ESC 4	36
ESC 5	36
SI	37
DC2	37
3.3.4. Line Spacing	38
LF	38
CR	38
ESC a n	38
ESC z n	39
ESC 0	39
ESC J n	40
ESC I n	40
3.3.5. Page Control Commands	41
FF	41
ESC C n	41
ESC C 0 n	42
VT	43
ESC B n1 n2…nk NUL	44
ESC B NUL	44
3.3.6. Horizontal Direction Printing Position	45
ESC l n	45
ESC Q n	46
HT	46
ESC D n1 n2…nk NUL	47
ESC D NUL	47
ESC GS A n1 n2	48
ESC GS R n1 n2	48
ESC GS a n	49
3.3.7. Download	50
ESC & c1 c2 n d1…d48	50
ESC & c1 c2 n	51
ESC % n	51
3.3.8. Bit Image Graphics	52
ESC K n1 n2 d1...dk	52
ESC L n1 n2 d1...dk	53
ESC k n1 n2 d1...dk	54
ESC X n1 n2 d1...dk	55
3.3.9. Logo	56
ESC FS q n [x11 x12 y11 y12 d1...dk]1...[xn1 xn2 yn1 yn2 d1...dk]n	56
ESC FS p n m	58
ESC RS L m	58
3.3.10. Bar Code	60
ESC b n1 n2 n3 n4 d1...dk RS	60
3.3.11. Cutter Control	62
ESC d n	62
3.3.12. External Device Drive	63
ESC BEL n1 n2	63
BEL	64
FS	64
SUB	65
EM	65
ESC GS BEL m t1 t2	66
ESC GS EM DC1 m n1 n2	67
ESC GS EM DC2 m n1 n2	68
3.3.13. Print Settings	69
ESC RS d n	69
ESC RS r n	70
3.3.14. Status	71
ESC RS a n	71
ESC ACK SOH	72
ENQ	72
EOT	72
ESC ACK CAN	72
ETB	73
ESC RS E n	73
ESC GS ETX s n1 n2	74
3.3.15. Kanji characters	77
ESC p	77
ESC q	77
ESC $ n	78
ESC s n1 n2	79
ESC t n1 n2	79
ESC r c1 c2 d1...dk	80
3.3.16. Others	81
CAN	81
ESC @	82
ESC GS # m N n1 n2 n3 n4 LF NUL	83
ESC ? LF NUL	84
ESC GS + m [t1 nL1 nH1 d11 d12 … d1k] 1	85
[t2 nL2 nH2 d21 d22 … d2k] 2 [tm nLm nHm dm1 dm2 … dmk] m	85
3.4. Raster Graphics Command Details	86
ESC * r R	87
ESC * r A	88
ESC * r B	89
ESC * r C	89
ESC * r D n NUL	90
ESC * r E n NUL	91
ESC * r F n NUL	92
ESC * r P n NUL	93
ESC * r Q n NUL	93
ESC * r m l n NUL	94
ESC * r m r n NUL	94
ESC * r T n NUL	95
ESC * r K n NUL	95
b n1 n2 data	96
k n1 n2 data	97
ESC * r Y n NUL	98
ESC FF NUL	99
ESC FF EOT	99
ESC * r N n NUL	99
ESC * r V m n NUL	100
ESC * r e s NUL	101
3.5. Black Mark Related Command Details	105
ESC d n	105
FF	106
ESC C n	106
ESC C 0 n	107
VT	108
ESC B n1 n2...nk NUL	108
ESC B NUL	108
3.6. USB Related Command Details	109
3.7. 2 Color Printing Command Details	110
ESC RS c n	110
ESC RS C n	111
ESC 4	113
ESC 5	113
ESC RS d n	114
ESC RS r n	115
ESC FS q n [x11 x12 y11 y12 d1...dk]1...[xn1 xn2 yn1 yn2 d1...dk]n	116
ESC FS p n m	118
3.8. Presenter Related Command Details	119
ESC SYN 0 n	119
ESC SYN 1 n	119
ESC SYN 3 n	120
ESC SYN 4 n	121
ESC GS SUB DC1 m t1 t2	122
ESC GS SUB DC2 m t1 t2	122
ESC GS SUB DC3 m t1 t2	123
3.9. Mark Command Details	124
ESC GS * 0 n m1 m2 m3 … mk	126
ESC GS * 1 h v	127
ESC GS * 2 m c w	127
ESC GS * W	128
ESC GS * C	128
3.10. AUTO LOGO Function Command Details	129
ESC GS / W	132
ESC GS / C	132
ESC GS / 1 n	133
ESC GS / 2 n	134
ESC GS / 3 nL nH d1 d2 … dk	135
ESC GS / 4 nL nH d1 d2 … dk	135
ESC GS / 5 n	136
ESC GS / 6 n	137
3.11. Two-dimensional Bar Code PDF417 Command Details	138
ESC GS x S 0 n p1 p2	140
ESC GS x S 1 n	140
ESC GS x S 2 n	140
ESC GS x S 3 n	141
ESC GS x D nL nH d1 d2 … dk	141
ESC GS x P	141
ESC GS x I	142
3.12. Details of the Print Starting Trigger Control Command	143
ESC GS g 0 m n	143
ESC GS g 1 m n	143
3.13. Two-Dimensional Bar Code QR Code Command Details	144
ESC GS y S 0 n	147
ESC GS y S 1 n	147
ESC GS y S 2 n	147
ESC GS y D 1 m nL nH d1 d2 … dk	148
ESC GS y D 2 a m1 n1L n1H d11 d12 • • • d1k m2 n2L n2H d21 d22 • • • d2k ml • • • dlk	149
ESC GS y P	150
ESC GS y I	150
3.14. Page Function Command Details	151
ESC GS h 0 k m n	151
3.15. Reduced Printing Function Command Details	152
ESC GS c h v	152
3.16. Page Mode Command Details	153
ESC GS P 0	153
ESC GS P 1	154
ESC GS P 2 n	154
ESC GS P 3 xL xH yL yH dxL dxH dyL dyH	155
ESC GS P 4 nL nH	157
ESC GS P 5 nL nH	158
ESC GS P 6	159
ESC GS P 7	159
ESC GS P 8	159
3.17. Text Search Command Details	160
ESC GS ) B pL pH fn [parameter]	160
<Function 48> ESC GS ) B pL pH fn m (fn = 48)	160
<Function 49> ESC GS ) B pL pH fn m (fn = 49)	161
<Function 50> ESC GS ) B pL pH fn m (fn = 50)	161
<Function 64> ESC GS ) B pL pH fn m k d1…dk (fn = 64)	162
<Function 65> ESC GS ) B pL pH fn m k1 k2 d1…dk (fn = 65)	162
<Function 80> ESC GS ) B pL pH fn m (fn = 80)	163
<Function 81> ESC GS ) B pL pH fn m (fn = 81)	163
<Function 96> ESC GS ) B pL pH fn m (fn = 96)	164
<Function 97> ESC GS ) B pL pH fn m (fn = 97)	164
3.18. Audio Command Details	165
ESC GS h 1 k m n	171
4. CHARACTER CODE TABLES	172
5. APPENDIX	173
5.1. Appendix 1: Bar Code Specification Details	173
5.1.1. Code 39	173
5.1.2. Interleaved 2 of 5	173
5.1.3. JAN/EAN/UPC	174
5.1.4. Code 128	175
5.1.5. Code 93	177
5.1.6. NW7 (CODERBAR)	177
5.2. Appendix 2: Status Specifications	178
5.2.1. ENQ Command Status	178
5.2.2. EOT Command Status	178
5.2.3. Automatic Status	179
5.2.4 Printer status transmission specification when using Ethernet I/F and Wireless LAN I/F	186
5.3. Appendix 3: Blank Code Page Configuration	188
5.4. Appendix 7 Maximum Number of Input Characters for Each Version of QR Code	191
5.5. Appendix 8 TSP828L Cut Command Specifications	195
5.6. Appendix 6 Explanation of Page Mode	196
5-6-1. Overview	196
5-6-2. Setting Values Using Each Command in Standard Mode and Page Mode	196
5-6-3. Print Data Expansion to the Print Region	197
5.7. 5-7) Appendix 7 Explanation of Print Startup Control Starting Printing When Set to Page Units	199
6. SPECIAL APPENDIX COMMAND LIST FOR EACH MODEL IN EACH I/F	200
6.1. RS-232C I/F	200
6.2. Parallel I/F • USB I/F (Ver2.0) • Powered USB I/F	205
6.3. USB I/F (Ver1.0) • Ethernet I/F (Silex Ver1.0)	211
6.4. Ethernet I/F / Wireless LAN I/F	217

Match case Limit results 1 per page

―――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――――

STAR Line Mode Command Specifications

3-126

Cell

Alignment Pattern

3.13.

Two-Dimensional Bar Code QR Code Command Details

* Note that QR code is a registered trademark of DENSO WEB.

This command is for printing 2-dimensional bar code QR codes.

There are four functions of the commands relating to

the 2-dimensional bar code QR codes, shown below.

(1) Set bar code type

(<ESC> <GS> “y” “S”)

(2) Set bar code data

(<ESC> <GS> “y” “D”)

(3) Set page mode

(Reserved)

(4) Print Bar code

(<ESC> <GS> “y” “P”)

(5) Set bar code type

(<ESC> <GS> “y” “I”)

The details of each function are described below.

(1) Set bar code type

These commands set the bar code type.

Because all initial values are set, use these only to make changes.

(See the

details for each setting below.)

<ESC> <GS> “y” “S” “0” Sets the model

Currently supported models are model 1 and model 2.

Model 2 has a configuration including an alignment bar to

improve its support of weight to handle skewing when codes are large.

<ESC> <GS> “y” “S” “1”

Sets the error correction level

QR codes can be read even if a part of the data is corrupted, by using error correction.

Raising this level increases the

size of the bar code because there is an increase in preparatory information.

<ESC> <GS> “y” “S” “2”

Specifies the size of the cell (One four squared region configuring the QR code)

The QR code is formed into a square of an equivalent size in the vertical and horizontal directions, but the size of the bar

code image that is generated depends on the cell size setting.

See Appendix 7 for details on the actual printed size of

the QR code.

These settings are individual settings.

Therefore, even though there may not be any particular problem in each of them,

there is the potential for an error to be generated.

(See the descriptions below.)

In such cases, the bar code will not be

generated and the (4) Print command (<ESC> <GS> “y” “P”) is ignored.

With the (5) Get bar code expansion

information command, an error code is returned.

• Error is generated when generating a bar code by the combination of each setting command.

• Print data exceeds the currently set print region

Therefore, it is recommended to use (5) Get bar code expansion information command (<ESC> <GS> “y” “I”) as a

means for checking for these errors prior to printing.