Oki OKIPOS408II OKIPOS 408II Programmer s Technical Reference - Page 184
Position for Presenter Paper Ninth Byte>, Details of the Presenter Paper Position
View all Oki OKIPOS408II manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 184 highlights
Bit Contents Status "0" "1" By model 408 407 RT322 TUP900 TSP1000 TSP828L 407II Ver. 4.3 or Ver. 3.2 or Ver. 3.2 or Ver. 1.2 or later later later later RT322 TUP500 408II FVP10 7 Fixed at "0" - - - - - - - - - - - - 6 Not Used (Fixed at "0") - NO NO NO OK NO NO NO NO NO NO NO 5 Not Used (Fixed at "0") - NO NO NO OK NO NO NO NO NO NO NO 4 Fixed at "0" - - - - - - - - - - - - (See table 3 Presenter Paper Position below) NO NO NO OK NO NO NO NO OK NO NO (See table 2 Presenter Paper Position below) NO NO NO OK NO NO NO NO OK NO NO (See table 1 Presenter Paper Position below) NO NO NO OK NO NO NO NO OK NO NO 0 Fixed at "0" - - - - - - - - - - - - • This status is valid only on models provided with a presenter. Models not provided with a presenter should send this status fixed at "0." • This status is made valid and invalid using the memory switch only on models provided with a presenter. When valid, the presenter paper position status is updated, but when invalid, the presenter paper position status is fixed at "0" and there is no change in status. • Details of the Presenter Paper Position bit bit bit Presenter Paper Position 3 2 1 0 0 0 Paper position 0 State where there is no paper in presenter 0 0 1 Paper position 1 State where paper is supplied (loop state) 0 1 0 Paper position 2 (Reserved) 0 1 1 Paper position 3 State where paper is discharged (Can be pulled out) 1 0 0 Paper position 4 (Reserved) 1 0 1 Paper position 5 (Reserved) 1 1 0 Paper position 6 State where paper is recovered 1 1 1 Paper position 7 State where paper is pulled out. • Presenter operation mode: Paper position status transition Operating Paper Presenter paper position state transition Mode Loop Take-up Internal recovery Loop Take-up Front Discharge No Loop Internal recovery No Loop Front Discharge Recovery Invalid Recovery Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper recovery) to Position 6 to Position 0 Pull out Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 7 to Position 0 Recovery Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 6 to Position 0 Pull out Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 7 to Position 0 Recovery Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 6 to Position 0 Pull out Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 7 to Position 0 Recovery Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 6 to Position 0 Pull out Position 0 to Position 1 to (Paper cut) to Position 3 to (Paper pull out) to Position 7 to Position 0 Recovery Position 0 to Position 1 to (Paper cut) to Position 6 to Position 0 Pull out Position 0 to Position 1 to (Paper cut) to Position 6 to Position 0 4. Note Do not use ENQ, EOT, and ESC ACK SOH when automatic status is valid. Invalidate the automatic status in advance using the DIPSW (memory switch) or the ESC RS a n command to query these. STAR Line Mode Command Specifications 5-12