Oki OKIPOS408II OKIPOS 408II Programmer s Technical Reference - Page 83

ESC GS # m N n1 n2 n3 n4 LF NUL [Name] Set memory switch [Code] ASCII ESC GS # m N n1 n2 n3 n4 LF NUL Hex. 1B 1D 23 m N n1 n2 n3 n4 0A 00 Decimal 27 29 35 m N n1 n2 n3 n4 10 0 [Defined Area] 48 ≤ n1 ≤ 57 ("0" ≤ n1 ≤ "9"), 65 ≤ n1 ≤ 70 ("A" ≤ n1 ≤ "F"), 97 ≤ n1 ≤ 102 ("a" ≤ n1 ≤ "f") 48 ≤ n2 ≤ 57 ("0" ≤ n2 ≤ "9"), 65 ≤ n2 ≤ 70 ("A" ≤ n2 ≤ "F"), 97 ≤ n2 ≤ 102 ("a" ≤ n2 ≤ "f") 48 ≤ n3 ≤ 57 ("0" ≤ n3 ≤ "9"), 65 ≤ n3 ≤ 70 ("A" ≤ n3 ≤ "F"), 97 ≤ n3 ≤ 102 ("a" ≤ n3 ≤ "f") 48 ≤ n4 ≤ 57 ("0" ≤ n4 ≤ "9"), 65 ≤ n4 ≤ 70 ("A" ≤ n4 ≤ "F"), 97 ≤ n4 ≤ 102 ("a" ≤ n4 ≤ "f") Spec. A m = 87, 84, 44, 43, 45, 64 （m = "W", "T 48 ≤ N ≤ 57 ("0" ≤ N ≤ "9"), 65 ≤ N ≤ (*)70 ("A" ≤ N ≤ (*)"F"), 97 ≤ N ≤ (*) 102, ("a" ≤ N f") Spec. B m = 87, 84, 44, 43, 45, 64 （m = "W", "T 48 ≤ N ≤ 57 ("0" ≤ N ≤ "9"), 65 ≤ N ≤ (*)70 ("A" ≤ N ≤ (*)"F"), 97 ≤ N ≤ (*) 102, ("a" ≤ N f") N = 85 (N = "U") User defined area Spec. C m = 87, 84, 44, 43, 45, 64, 42 (m = "W", "T 48 ≤ N ≤ 57 ("0" ≤ N ≤ "9"), 65 ≤ N ≤ (*)70 ("A" ≤ N ≤ (*)"F"), 97 ≤ N ≤ (*) 102, ("a" ≤ N f") N = 85 (N = "U") User defined area (*) The memory switch defined area differs according to the model. [Initial Value] [Function] - - Sends command to write after defining memory switch using the definition command specified by the following classes. Memory switch information defined by the command to write is written to the volatile memory. When writing to the volatile memory by the command to write, the printer executes a reset. This command exists in models that have the specifications of A, B and C indicated in the above defined areas. On models that have specification C, you can load the default settings by specifying m = 42 (*). Models having specifications B can register any 16 bit data by specifying N = 85 ("U"). (See the "Special Appendix, Command Table per Model" for details per model.) Functions Class m N n1 n2 n3 n4 Definition data write and reset Write "W" Definition data write and reset and Write "T" self print Data definition (data specification) Definition ", " Data definition (specify bit and set) Definition "+" Data definition (specify bit and clear) Definition "-" Definition data (all data initialized) Definition "@" Definition data (load default settings) Definition "*" Fixed at "0" Fixed at "0000" Fixed at "0" Fixed at "0000" N N N Fixed at "0" Fixed at "0" n1 n2 n3 n4 n1 n2 n3 n4 n1 n2 n3 n4 Fixed at "0000" Fixed at "0000" • m: Mode selection • N: Memory switch number to specify • n1 n2 n3 n4: Specify data m = (",") Specify data m = ("+") Bit number to set m = ("-") Bit number to clear STAR Line Mode Command Specifications 3-65