Panasonic AJHPX2700G AJHPX2700G User Guide - Page 149

Inspecting the Memory Recording Functions, Inspecting the Audio Level Manual Adjustment

Get Panasonic AJHPX2700G - MEMORY CARD CAMERA-RECORDER PDF manuals and user guides View all Panasonic AJHPX2700G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 149 highlights

Maintenance and Inspections Inspecting the Memory Recording Functions Make sure you successively carry out the inspections from [1. Inspecting the P2 Card Recording] to [4. Inspecting the Earphone and Speaker]. 1. Inspecting the P2 Card Recording 1 Check on the display inside the viewfinder that the remaining P2 card recording capacity is sufficient. Please refer to [P2 Card Remaining Free Space/ capacity Indication] (page 82) for information about P2 card remaining recording capacity. 2 Set the TCG switch to [R-RUN]. 3 Set the DISPLAY switch to [TC]. 4 Press the camera's REC START/STOP button to check the following items: The P2 access LED blinks in orange. The REC lamp inside the viewfinder lights up. System warnings do not appear inside the viewfinder. 5 Press the camera's REC START/STOP button again. This step confirms that the P2 access LED is on and showing orange, and the REC lamp in the viewfinder is turned off. 6 Press the LIGHT button to check that the screen brightness in the display window increases. 7 Press the PLAY/PAUSE button to check that the clip that has just been shot is played back from the beginning. Check that recording and playback operate properly. 8 When multiple P2 cards are inserted into the P2 card slots, press the user button to which the SLOT SEL function has been assigned in order to select the P2 card used for recording. Repeat the operations in steps 4 to 5 and 7 to check that recording and playback operate properly. 2. Inspecting the Audio Level Automatic Adjustment 1 Set the AUDIO SELECT CH1 and CH2 switches to [AUTO]. 2 Set the AUDIO IN CH1 and CH2 switches to [FRONT]. 3 Aim the microphone connected to the MIC IN jack at an appropriate sound source. Then, check that the level displays for both CH1 and CH2 change according to the sound level. 3. Inspecting the Audio Level Manual Adjustment 1 Set the AUDIO IN CH1 and CH2 switches to [FRONT]. 2 Set the AUDIO SELECT CH1 and CH2 switches to [MAN]. 3 Turn the AUDIO LEVEL CH1 and CH2 controls. Check that the level display increases when the controls are turned to the right. 4. Inspecting the Earphone and Speaker 1 Turn the MONITOR control to check that the speaker volume changes. 2 Connect an earphone to the PHONES jack. Check that the speaker is turned off and the microphone sound can be heard from the earphone. 3 Turn the MONITOR control to check that the earphone volume changes. 5. Inspection for Using an External Microphone 1 Connect an external microphone to the AUDIO IN CH1 and CH2 connectors. 2 Set the AUDIO IN CH1 and CH2 switches to [REAR]. 3 Set the LINE/MIC/+48V selector switches on the rear panel to [MIC] or [+48V], depending on the power supply type of the external microphone. MIC: For a microphone with internal power supply. +48V: For a microphone with external power supply. 4 Aim the microphone at a sound source. Then check that the audio level meter in the display window and the audio level display inside the viewfinder change according to the sound level. The channels can also be checked separately by connecting a single microphone to each channel. 149 Maintenance and Inspections: Inspections Before Shooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
149
Maintenance and Inspections: Inspections Before Shooting
Maintenance and Inspections
Make sure you successively carry out the inspections from
[1. Inspecting the P2 Card Recording] to [4. Inspecting the
Earphone and Speaker].
1.
Inspecting the P2 Card Recording
1
Check on the display inside the viewfinder that the
remaining P2 card recording capacity is sufficient.
Please refer to [P2 Card Remaining Free Space/
capacity Indication] (page 82) for information about P2
card remaining recording capacity.
2
Set the TCG switch to [R-RUN].
3
Set the DISPLAY switch to [TC].
4
Press the camera’s REC START/STOP button to check
the following items:
y
The P2 access LED blinks in orange.
y
The REC lamp inside the viewfinder lights up.
y
System warnings do not appear inside the viewfinder.
5
Press the camera’s REC START/STOP button again.
This step confirms that the P2 access LED is on and
showing orange, and the REC lamp in the viewfinder is
turned off.
6
Press the LIGHT button to check that the screen
brightness in the display window increases.
7
Press the PLAY/PAUSE button to check that the clip that
has just been shot is played back from the beginning.
Check that recording and playback operate properly.
8
When multiple P2 cards are inserted into the P2 card
slots, press the user button to which the SLOT SEL
function has been assigned in order to select the P2
card used for recording.
Repeat the operations in steps
4
to
5
and
7
to check that
recording and playback operate properly.
2.
Inspecting the Audio Level Automatic
Adjustment
1
Set the AUDIO SELECT CH1 and CH2 switches to
[AUTO].
2
Set the AUDIO IN CH1 and CH2 switches to [FRONT].
3
Aim the microphone connected to the MIC IN jack at an
appropriate sound source. Then, check that the level
displays for both CH1 and CH2 change according to the
sound level.
3.
Inspecting the Audio Level Manual Adjustment
1
Set the AUDIO IN CH1 and CH2 switches to [FRONT].
2
Set the AUDIO SELECT CH1 and CH2 switches to
[MAN].
3
Turn the AUDIO LEVEL CH1 and CH2 controls.
Check that the level display increases when the controls
are turned to the right.
4.
Inspecting the Earphone and Speaker
1
Turn the MONITOR control to check that the speaker
volume changes.
2
Connect an earphone to the PHONES jack.
Check that the speaker is turned off and the microphone
sound can be heard from the earphone.
3
Turn the MONITOR control to check that the earphone
volume changes.
5.
Inspection for Using an External Microphone
1
Connect an external microphone to the AUDIO IN CH1
and CH2 connectors.
2
Set the AUDIO IN CH1 and CH2 switches to [REAR].
3
Set the LINE/MIC/+48V selector switches on the rear
panel to [MIC] or [+48V], depending on the power
supply type of the external microphone.
MIC:
For a microphone with internal power supply.
+48V:
For a microphone with external power supply.
4
Aim the microphone at a sound source. Then check that
the audio level meter in the display window and the
audio level display inside the viewfinder change
according to the sound level.
The channels can also be checked separately by
connecting a single microphone to each channel.
Inspecting the Memory Recording Functions