Panasonic AV-UHS500 4K Switcher Operating Instructions - Page 100

Color Corrector, Color Corrector settings, Process control, Tone curve

Get Panasonic AV-UHS500 PDF manuals and user guides View all Panasonic AV-UHS500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 100 highlights

Input/output signal settings Color Corrector Make settings for the Color Correctors built in to SDI IN5 to SDI IN8 and the following optional units. 1 On the Input sub menu, use [F2] to select the input to be set using the Select item.  Refer to "Input signal settings". Color Corrector settings 1 Use [F1] to display the C/C Operation sub menu. Tone curve Corrects the tone of the input signal. Set the tone curve to adjust the brightness, contrast, etc., of images. You can adjust the white balance and the color tone by separately adjusting each of the R, G, and B colors. 2 Use [F2] to set the Color Corrector to enable (On)/ disable (Off). 3 Use [F3] to set the color range of the input signal in the Limit item. Off No limit on color range. 108 The amplitude level of each color (R, G, B) is limited to between 0% and 108%. 104 The amplitude level of each color (R, G, B) is limited to between 0% and 104%. 100 The amplitude level of each color (R, G, B) is limited to between 0% and 100%.  Tone1 Black  Tone2 Gray L  Tone3 Gray H  Tone4 White Tone1 Black Tone2 Gray L Tone3 Gray H Tone4 White Adjusts the black level. Adjusts the gray Low level. Adjusts the gray High level. Adjusts the white level. 1 Use [F1] to display the C/C Tone1 Black sub menu. Process control 1 Use [F1] to display the C/C Process sub menu. 2 Use [F2] to set the gain value of the Y signal in the Y-Gain item. 3 Use [F3] to set the value of the pedestal level in the Pedestal item. 4 Use [F4] to set the gain value of the saturation in the C-Gain item. 5 Use [F5] to set the amount of change of the color hue in the Hue item. 2 Use [F2] to adjust the R signal of the black level in the Red item. 3 Use [F3] to adjust the G signal of the black level in the Green item. 4 Use [F4] to adjust the B signal of the black level in the Blue item. 5 Use [F5] to make the link settings for the adjustment value in the RGB Link item. Off RGB can be independently set in each of the C/C Tone1 Black, C/C Tone2 Gray L, C/C Tone3 Gray H, and C/C Tone4 White sub menus. On The Red setting value is set in Green and Blue in each of the C/C Tone1 Black, C/C Tone2 Gray L, C/C Tone3 Gray H, and C/C Tone4 White sub menus. 100

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
100
Input/output signal settings
Color Corrector
Make settings for the Color Correctors built in to SDI IN5 to
SDI IN8 and the following optional units.
1
On the Input sub menu, use [F2] to select the input to
be set using the Select item.
Refer to “Input signal settings”.
Color Corrector settings
1
Use [F1] to display the C/C Operation sub menu.
2
Use [F2] to set the Color Corrector to enable (On)/
disable (Off).
3
Use [F3] to set the color range of the input signal in the
Limit item.
Off
No limit on color range.
108
The amplitude level of each color (R, G, B) is
limited to between 0% and 108%.
104
The amplitude level of each color (R, G, B) is
limited to between 0% and 104%.
100
The amplitude level of each color (R, G, B) is
limited to between 0% and 100%.
Process control
1
Use [F1] to display the C/C Process sub menu.
2
Use [F2] to set the gain value of the Y signal in the
Y-Gain item.
3
Use [F3] to set the value of the pedestal level in the
Pedestal item.
4
Use [F4] to set the gain value of the saturation in the
C-Gain item.
5
Use [F5] to set the amount of change of the color hue in
the Hue item.
Tone curve
Corrects the tone of the input signal.
Set the tone curve to adjust the brightness, contrast, etc., of
images.
You can adjust the white balance and the color tone by
separately adjusting each of the R, G, and B colors.
Tone1 Black
Tone2 Gray L
Tone3 Gray H
Tone4 White
Tone1 Black
Adjusts the black level.
Tone2 Gray L
Adjusts the gray Low level.
Tone3 Gray H
Adjusts the gray High level.
Tone4 White
Adjusts the white level.
1
Use [F1] to display the C/C Tone1 Black sub menu.
2
Use [F2] to adjust the R signal of the black level in the
Red item.
3
Use [F3] to adjust the G signal of the black level in the
Green item.
4
Use [F4] to adjust the B signal of the black level in the
Blue item.
5
Use [F5] to make the link settings for the adjustment
value in the RGB Link item.
Off
RGB can be independently set in each of
the C/C Tone1 Black, C/C Tone2 Gray L, C/C
Tone3 Gray H, and C/C Tone4 White sub
menus.
On
The Red setting value is set in Green and
Blue in each of the C/C Tone1 Black, C/C
Tone2 Gray L, C/C Tone3 Gray H, and C/C
Tone4 White sub menus.