Home » Panasonic Manuals » Video Cameras » Panasonic AV-UHS500 » Manual Viewer

Panasonic AV-UHS500 4K Switcher Operating Instructions - Page 77

Setting events using the menus, Registering marks, Setting the event duration, PAUSE, GPI-Out

View all Panasonic AV-UHS500 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Basic operations Setting events using the menus  Registering marks Marks can be registered and events inserted at the event points. ppPause ppClip playback ppGPI-Out output 1 Use , 0/10 and . >> to select the event where the mark is to be registered or the event inserted. 2 Press the SHOT EVENT button to display the Event Memory menu. 3 Use [F1] to display the Mark sub menu. 4 Use [F2] (PAUSE item), [F3] (CLIP item) or [F4] (GPI-Out item) to select the item. PAUSE CLIP GPI-Out When "On" is selected and the mark is registered in the event point, playback is paused at the mark position during event playback. "||" appears above the timeline. When "Clip1" or "Clip2" is selected and the mark is registered in the event point, the clip is played back at the mark position during event playback. " " appears above the timeline. When a GPI output port from "GPI-O1" to "GPI-O19" is selected and the mark is registered in the event point, pulse signals are output from the GPI Output port at the mark position during event playback. " " appears above the timeline.  F or the Config menu  GPI-Out Port 1/5 sub menu to GPI-Out Port 5/5 sub menu  Assign item, check that the selected GPI output port is set to "Event MEM". 5 Press 6 MOD to register the mark. In addition, press 4 INS to insert the event. To cancel the mark registration or event insertion, press the C UNDO button.  Setting the event duration The lengths of the events can be set. 1 Use , 0/10 and . >> to select the event to be modified. 2 Press the SHOT EVENT button to display the Event Memory menu. 3 Use [F1] to display the Event Duration sub menu. 4 Use [F2] to set the event length. 5 Press [F3] to enter the duration. To cancel what has been modified, press the C UNDO button.  Setting the total duration The total length of all the events from start to end can be set. When the total duration is changed, the durations of the events contained in the event memories are re-calculated using the duration ratio prior to the change. However, the shortest duration of an event cannot be shorter than one frame. 1 Press the [EVENT MEM] button and light its indicator. 2 Press the [RECALL] button to light its indicator, and use the -/+ PAGE button and number keys (1 to 10) to select the event memory to be modified.  Refer to "Recalling the operations stored in the memory (Recall)". 3 Press the SHOT EVENT button to display the Event Memory menu. 4 Use [F1] to display the Total Duration sub menu. 5 Use [F2] to set the event length. 6 Press [F3] to enter the duration. ppIf no more events can be contained in the total duration which already has many events and which has been changed, the number of frames will be forcibly adjusted. 77

Section	Page
Read this first!	3
Contents	8
Before use	11
Overview	11
Concerning the ratings display	11
Disclaimer of warranty	11
Network security	11
Precautions for use	12
Installation precautions	13
Features	14
Accessories	15
Installation and connections	15
How to install the option units	15
Parts and their functions	17
Control panel	17
Crosspoint area	18
Memory/wipe pattern/number key area	19
User button area	20
Transition area	20
Display area	22
Positioner area	24
Memory card area	25
Rear panel area	26
Preparations	27
Turning the unit’s power on and off	27
Basic menu operations	28
Menu configuration and operations	28
Keyboard screen operations	30
Menu delegation function	30
Setting the system format	31
Setting the date and time	31
Basic operations	32
Background transition	32
Selecting the bus	32
Selecting the bus using the SHIFT function	32
Selecting the bus mode	33
Selecting the transition mode	33
Manual transition	34
Auto transition	34
Cut transition	34
Wipe	35
Selecting the wipe pattern	35
Selecting the wipe direction	36
Wipe decorations (border, soft effect)	36
Setting the wipe start position	37
Modifying wipe	37
Setting the latency	38
Key	39
Selecting the key type	39
Selecting the key material	40
Key transitions	42
Key preview	44
Adjusting the luminance key and linear key	45
Adjusting the chroma key	45
Key decorations	49
Masking the key signals	50
Flying key	51
Setting the priority	51
PinP (picture in picture)	52
Selecting the PinP channel and material	52
Selecting Shape	52
PinP adjustments	53
Linking Key PinP and DSK PinP	53
PinP decorations	54
Trimming settings	55
DSK (downstream key)	56
Selecting the DSK type	56
Selecting the DSK material	57
DSK transitions	58
DSK preview	59
DSK adjustments	59
Masking the DSK signals	60
Key Link	61
FTB (Fade to Black)	61
Internal color signals	62
Setting the color background	62
Setting the Wash effect	63
Switching the AUX output	64
Selecting the AUX output materials	64
AUX1/2 transitions	64
Setting enable/disable for the AUX1/2 transition	65
Memory	66
Memory registration	67
Memory recall items	67
Storing the settings in the memory (Store)	68
Recalling the operations stored in the memory (Recall)	69
Memory preview	70
Deleting the operations stored in the memory (Delete)	70
Selecting the buses whose settings are to be registered and or played back	71
Setting effect dissolve (shot memory)	72
Editing event memory timelines	73
Macro memory settings	78
Registering memories (Register)	79
Video memories	80
Recording still images (Still)	81
Recording moving images (Clip)	82
Saving Images in Flash Memory	83
Playing back moving images (Clip)	84
Memory card	86
Initializing the memory cards	89
Saving data on memory cards	89
Loading data from memory cards	90
Deleting files on memory cards	91
Displaying the memory card information	92
Waveform monitor settings	93
Input/output signal settings	94
Input signal settings	94
Settings for the exclusionary input connectors	96
Settings for the color range for input signals	96
Checking the input signal status	97
Setting the frame synchronizer	97
Setting the delay amount	98
Freezing the input signals	98
Setting the material names	99
Setting the up-converter	99
Color Corrector	100
Setting the HDMI input signals	103
Displaying the HDMI input signal information	104
Output signal settings	105
Assigning the output signals	106
Setting the SDI output color range	106
Setting the HDMI output signals	107
Setting the down-converter (option)	108
Setting the sync signals	109
Adjusting the output signal phase	109
Setting the multi view display	113
Setting the screen layout	113
Setting the split frame and characters	114
Setting the tally displays	114
Changing the material names	115
Setting the level meters	115
Setting the input signal marks	116
Setting the markers	116
Ancillary settings for the AUX bus, PGM, and PVW	117
System settings	118
Setting the system format	118
Switcher mode settings	118
Dynamic range and color range settings	118
Setting the crosspoints	119
Assigning signals to the crosspoints	119
Setting the crosspoint switching	120
Button assignments	121
Setting the user buttons	121
Setting the date and time	122
Network settings	122
Setting the built-in display backlight and button illumination	123
Status displays	124
Alarm status displays	124
Alarm message	124
Displaying information about the version and optional units	125
Initialization	126
Initializing setting data	126
Initializing fader	126
Remote camera link functions	127
Settings for connections to remote cameras	128
Selecting the terminals for remote camera connection	128
IP address settings	128
Remote camera port settings	129
Remote camera authentication settings	129
Checking the remote camera connection status	129
Remote camera operation direction settings	130
Remote camera tally control settings	130
Selecting the cameras to be operated	131
Controlling in the camera control screen	132
Remote camera settings	133
Selecting the remote camera, checking information, and controlling power	133
Remote camera control speed settings	134
Remote camera on-screen menu and color bar settings	134
Remote camera lens control settings	135
Remote camera image adjustment settings	135
Remote camera preset memory playback settings	136
Disabling remote camera control	136
Controlling in the camera preset memory screen	137
Storing preset memories	139
Recalling preset memories	139
Deleting preset memories	139
Deleting a page of preset memories	140
External interfaces	141
Setting the GPI I/O	141
LAN	144
Controlling with external panels	145
Preparations	145
External panel settings	145
Settings on this unit when external panels are connected	145
List of bus IDs and source IDs	146
Appearance	149
Specifications	150
Setting menu table	152
Appendix (glossary)	181

Match case Limit results 1 per page

Basic operations

Setting events using the menus

Registering marks

Marks can be registered and events inserted at the event

points.

Pause

Clip playback

GPI-Out output

Use

0/10

and

to select the event where

the mark is to be registered or the event inserted.

Press the

SHOT

EVENT

button to display the Event Memory

menu.

Use [F1] to display the Mark sub menu.

Use [F2] (PAUSE item), [F3] (CLIP item) or [F4]

(GPI-Out item) to select the item.

PAUSE

When “On” is selected and the mark is

registered in the event point, playback is

paused at the mark position during event

playback.

“||” appears above the timeline.

CLIP

When “Clip1” or “Clip2” is selected and the

mark is registered in the event point, the clip

is played back at the mark position during

event playback.

“

” appears above the timeline.

GPI-Out

When a GPI output port from “GPI-O1”

to “GPI-O19” is selected and the mark is

registered in the event point, pulse signals

are output from the GPI Output port at the

mark position during event playback.

“

” appears above the timeline.

For the Conﬁg menu



GPI-Out Port 1/5

sub menu to GPI-Out Port 5/5 sub menu



Assign item, check that the selected GPI

output port is set to “Event MEM”.

Press

MOD

to register the mark.

In addition, press

INS

to insert the event.

To cancel the mark registration or event insertion, press

the

UNDO

button.

Setting the event duration

The lengths of the events can be set.

Use

0/10

and

to select the event to be

modified.

Press the

SHOT

EVENT

button to display the Event Memory

menu.

Use [F1] to display the Event Duration sub menu.

Use [F2] to set the event length.

Press [F3] to enter the duration.

To cancel what has been modified, press the

UNDO

button.

Setting the total duration

The total length of all the events from start to end can be set.

When the total duration is changed, the durations of the

events contained in the event memories are re-calculated

using the duration ratio prior to the change.

However, the shortest duration of an event cannot be shorter

than one frame.

Press the [EVENT MEM] button and light its indicator.

Press the [RECALL] button to light its indicator, and use

the

-/+

PAGE

button and number keys (1 to 10) to select the

event memory to be modified.



Refer to “Recalling the operations stored in the

memory (Recall)”.

Press the

SHOT

EVENT

button to display the Event Memory

menu.

Use [F1] to display the Total Duration sub menu.

Use [F2] to set the event length.

Press [F3] to enter the duration.

If no more events can be contained in the total duration

which already has many events and which has been

changed, the number of frames will be forcibly adjusted.