Home » Panasonic Manuals » Video Cameras » Panasonic AV-UHS500 » Manual Viewer

Panasonic AV-UHS500 4K Switcher Operating Instructions - Page 145

Controlling with external panels, Preparations, External panel settings

View all Panasonic AV-UHS500 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 145 highlights

External interfaces Controlling with external panels With this unit, you can perform the following operations from external panels (*) connected via an IP network: pp Select materials for each bus pp Execute video transitions pp Play back macro memories pp Play back shot memories *: This unit supports the LBP series from LAWO. Consult LAWO for LBP series settings and operations. Preparations Use a LAN cable to connect the external panel to the LAN connector on the back of the unit. It is possible to connect a maximum of 20 external panels. When connecting multiple external panels, connect via a hub. External panel settings Check the following settings on this unit, then make the settings on the connected external panels: pp System menu  Network1 sub menu Take the address value set in the IP Address item of this sub menu and set it as the IP address of the device that will be the target of the external panel operations. pp System menu  ExtPanel Info sub menu Take the port number set in the Port No item of this sub menu and set it as the port number of the device that will be the target of the external panel operations. Also set the subnet mask (Network2 sub menu) and the default gateway (Network3 sub menu) according to the network environment connected. Settings on this unit when external panels are connected Receiving port number settings 1 Press the CONF SYS button to light its indicator, and display the System menu. 2 Use [F1] to display the ExtPanel Info sub menu. 3 Use [F2] to set the receiving port number used by this unit. Possible setting range 62000 to 65535 Default value 62010 Shot memory playback target settings Set the playback targets for when shot memories of this unit are played back by operations on the external panels. 1 Press the CONF SYS button to light its indicator, and display the System menu. 2 Use [F1] to display the ExtPanelIP SMEMRecall1/2 sub menu. 3 Use [F2] to [F4] to set the playback targets for the shot memory. ppME, DSK, AUX, color background, and crosspoint area can be individually turned ON/OFF. 145

Section	Page
Read this first!	3
Contents	8
Before use	11
Overview	11
Concerning the ratings display	11
Disclaimer of warranty	11
Network security	11
Precautions for use	12
Installation precautions	13
Features	14
Accessories	15
Installation and connections	15
How to install the option units	15
Parts and their functions	17
Control panel	17
Crosspoint area	18
Memory/wipe pattern/number key area	19
User button area	20
Transition area	20
Display area	22
Positioner area	24
Memory card area	25
Rear panel area	26
Preparations	27
Turning the unit’s power on and off	27
Basic menu operations	28
Menu configuration and operations	28
Keyboard screen operations	30
Menu delegation function	30
Setting the system format	31
Setting the date and time	31
Basic operations	32
Background transition	32
Selecting the bus	32
Selecting the bus using the SHIFT function	32
Selecting the bus mode	33
Selecting the transition mode	33
Manual transition	34
Auto transition	34
Cut transition	34
Wipe	35
Selecting the wipe pattern	35
Selecting the wipe direction	36
Wipe decorations (border, soft effect)	36
Setting the wipe start position	37
Modifying wipe	37
Setting the latency	38
Key	39
Selecting the key type	39
Selecting the key material	40
Key transitions	42
Key preview	44
Adjusting the luminance key and linear key	45
Adjusting the chroma key	45
Key decorations	49
Masking the key signals	50
Flying key	51
Setting the priority	51
PinP (picture in picture)	52
Selecting the PinP channel and material	52
Selecting Shape	52
PinP adjustments	53
Linking Key PinP and DSK PinP	53
PinP decorations	54
Trimming settings	55
DSK (downstream key)	56
Selecting the DSK type	56
Selecting the DSK material	57
DSK transitions	58
DSK preview	59
DSK adjustments	59
Masking the DSK signals	60
Key Link	61
FTB (Fade to Black)	61
Internal color signals	62
Setting the color background	62
Setting the Wash effect	63
Switching the AUX output	64
Selecting the AUX output materials	64
AUX1/2 transitions	64
Setting enable/disable for the AUX1/2 transition	65
Memory	66
Memory registration	67
Memory recall items	67
Storing the settings in the memory (Store)	68
Recalling the operations stored in the memory (Recall)	69
Memory preview	70
Deleting the operations stored in the memory (Delete)	70
Selecting the buses whose settings are to be registered and or played back	71
Setting effect dissolve (shot memory)	72
Editing event memory timelines	73
Macro memory settings	78
Registering memories (Register)	79
Video memories	80
Recording still images (Still)	81
Recording moving images (Clip)	82
Saving Images in Flash Memory	83
Playing back moving images (Clip)	84
Memory card	86
Initializing the memory cards	89
Saving data on memory cards	89
Loading data from memory cards	90
Deleting files on memory cards	91
Displaying the memory card information	92
Waveform monitor settings	93
Input/output signal settings	94
Input signal settings	94
Settings for the exclusionary input connectors	96
Settings for the color range for input signals	96
Checking the input signal status	97
Setting the frame synchronizer	97
Setting the delay amount	98
Freezing the input signals	98
Setting the material names	99
Setting the up-converter	99
Color Corrector	100
Setting the HDMI input signals	103
Displaying the HDMI input signal information	104
Output signal settings	105
Assigning the output signals	106
Setting the SDI output color range	106
Setting the HDMI output signals	107
Setting the down-converter (option)	108
Setting the sync signals	109
Adjusting the output signal phase	109
Setting the multi view display	113
Setting the screen layout	113
Setting the split frame and characters	114
Setting the tally displays	114
Changing the material names	115
Setting the level meters	115
Setting the input signal marks	116
Setting the markers	116
Ancillary settings for the AUX bus, PGM, and PVW	117
System settings	118
Setting the system format	118
Switcher mode settings	118
Dynamic range and color range settings	118
Setting the crosspoints	119
Assigning signals to the crosspoints	119
Setting the crosspoint switching	120
Button assignments	121
Setting the user buttons	121
Setting the date and time	122
Network settings	122
Setting the built-in display backlight and button illumination	123
Status displays	124
Alarm status displays	124
Alarm message	124
Displaying information about the version and optional units	125
Initialization	126
Initializing setting data	126
Initializing fader	126
Remote camera link functions	127
Settings for connections to remote cameras	128
Selecting the terminals for remote camera connection	128
IP address settings	128
Remote camera port settings	129
Remote camera authentication settings	129
Checking the remote camera connection status	129
Remote camera operation direction settings	130
Remote camera tally control settings	130
Selecting the cameras to be operated	131
Controlling in the camera control screen	132
Remote camera settings	133
Selecting the remote camera, checking information, and controlling power	133
Remote camera control speed settings	134
Remote camera on-screen menu and color bar settings	134
Remote camera lens control settings	135
Remote camera image adjustment settings	135
Remote camera preset memory playback settings	136
Disabling remote camera control	136
Controlling in the camera preset memory screen	137
Storing preset memories	139
Recalling preset memories	139
Deleting preset memories	139
Deleting a page of preset memories	140
External interfaces	141
Setting the GPI I/O	141
LAN	144
Controlling with external panels	145
Preparations	145
External panel settings	145
Settings on this unit when external panels are connected	145
List of bus IDs and source IDs	146
Appearance	149
Specifications	150
Setting menu table	152
Appendix (glossary)	181

Match case Limit results 1 per page

145

External interfaces

Controlling with external panels

With this unit, you can perform the following operations from

external panels (*) connected via an IP network:

Select materials for each bus

Execute video transitions

Play back macro memories

Play back shot memories

*: This unit supports the LBP series from LAWO. Consult

LAWO for LBP series settings and operations.

Preparations

Use a LAN cable to connect the external panel to the LAN

connector on the back of the unit.

It is possible to connect a maximum of 20 external panels.

When connecting multiple external panels, connect via a hub.

External panel settings

Check the following settings on this unit, then make the

settings on the connected external panels:

System menu



Network1 sub menu

Take the address value set in the IP Address item of this

sub menu and set it as the IP address of the device that

will be the target of the external panel operations.

System menu



ExtPanel Info sub menu

Take the port number set in the Port No item of this sub

menu and set it as the port number of the device that will

be the target of the external panel operations.

Also set the subnet mask (Network2 sub menu) and the

default gateway (Network3 sub menu) according to the

network environment connected.

Settings on this unit when external panels

are connected

Receiving port number settings

Press the

CONF

SYS

button to light its indicator, and display

the System menu.

Use [F1] to display the ExtPanel Info sub menu.

Use [F2] to set the receiving port number used by this

unit.

Possible setting range

62000 to 65535

Default value

62010

Shot memory playback target settings

Set the playback targets for when shot memories of this unit

are played back by operations on the external panels.

Press the

CONF

SYS

button to light its indicator, and display

the System menu.

Use [F1] to display the ExtPanelIP SMEMRecall1/2 sub

menu.

Use [F2] to [F4] to set the playback targets for the shot

memory.

ME, DSK, AUX, color background, and crosspoint area

can be individually turned ON/OFF.