Home » Panasonic Manuals » Video Cameras » Panasonic AV-UHS500 » Manual Viewer

Panasonic AV-UHS500 4K Switcher Operating Instructions - Page 26

Rear panel area, Option slot SLOT B [EXPANSION SLOT B]

View all Panasonic AV-UHS500 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Parts and their functions Rear panel area     EXPANTION SLOT B  TALLY/GPI 2 TALLY/GPI 1 BOOT REF SV NM EXPANTION SLOT A  HDMI IOUT 12G SDI OUT HDMI IN 2 1 5 4 3 2 1 2 1 12G SDI IN LAN 8 7 6 5 4 3 2 1 SIGNAL GND POWER ON OFF AC IN ～        P ower switch [POWER] When the power switch is turned on, the POWER indicator () lights up, and the unit can be operated.  HDMI output connectors [HDMI OUT 1, 2] Connect to external devices with an HDMI cable.  SDI signal output connectors [12G SDI OUT 1 to 5] Assignable with menus  HDMI input connectors [HDMI IN 1, 2] Connect to external devices with an HDMI cable.  SDI signal input connectors [12G SDI IN 1 to 8] 12G SDI IN 1 to 12G SDI IN 4 can use the up-converter function.  LAN connector [LAN] (RJ-45) (1000Base-TX)  Refer to "External interfaces".  Ground connector [SIGNAL GND] Connect to the system's earth ground.  AC power input socket [AC IN ] (AC 100 V to 240 V, 50/60 Hz) Connect one end of the supplied power cable to this socket and the other end to the AC outlet. The supplied power cable comes with a 3-pin power plug. Be absolutely sure to plug it into a 3-point power outlet as the power source in order to earth the unit securely. If a 3-point power outlet is not available for this connection, be absolutely sure to consult your dealer.  Option slot SLOT A [EXPANSION SLOT A]  Option slot SLOT B [EXPANSION SLOT B] Each of these is an input/output option slot. A SDI input unit, HDMI output unit or other optional unit can be installed in these slots. For details, refer to "How to install the optional units" and the operating instructions of the unit concerned.  TALLY/GPI input/output connectors [TALLY/GPI 1, TALLY/GPI 2] (D-sub 15-pin, female, inch screw)  Refer to "External interfaces".  BOOT switch [BOOT SV NM] This switch is used for maintenance purposes. For normal operations, select the "NM" (normal) position.  R eference input connector/BB output connector [REF] Loop-through output in the external sync mode. If the loop-through output is not going to be used, provide a 75-ohm termination. BB signals output from both connectors in the internal sync mode.  Cooling fan 26

Section	Page
Read this first!	3
Contents	8
Before use	11
Overview	11
Concerning the ratings display	11
Disclaimer of warranty	11
Network security	11
Precautions for use	12
Installation precautions	13
Features	14
Accessories	15
Installation and connections	15
How to install the option units	15
Parts and their functions	17
Control panel	17
Crosspoint area	18
Memory/wipe pattern/number key area	19
User button area	20
Transition area	20
Display area	22
Positioner area	24
Memory card area	25
Rear panel area	26
Preparations	27
Turning the unit’s power on and off	27
Basic menu operations	28
Menu configuration and operations	28
Keyboard screen operations	30
Menu delegation function	30
Setting the system format	31
Setting the date and time	31
Basic operations	32
Background transition	32
Selecting the bus	32
Selecting the bus using the SHIFT function	32
Selecting the bus mode	33
Selecting the transition mode	33
Manual transition	34
Auto transition	34
Cut transition	34
Wipe	35
Selecting the wipe pattern	35
Selecting the wipe direction	36
Wipe decorations (border, soft effect)	36
Setting the wipe start position	37
Modifying wipe	37
Setting the latency	38
Key	39
Selecting the key type	39
Selecting the key material	40
Key transitions	42
Key preview	44
Adjusting the luminance key and linear key	45
Adjusting the chroma key	45
Key decorations	49
Masking the key signals	50
Flying key	51
Setting the priority	51
PinP (picture in picture)	52
Selecting the PinP channel and material	52
Selecting Shape	52
PinP adjustments	53
Linking Key PinP and DSK PinP	53
PinP decorations	54
Trimming settings	55
DSK (downstream key)	56
Selecting the DSK type	56
Selecting the DSK material	57
DSK transitions	58
DSK preview	59
DSK adjustments	59
Masking the DSK signals	60
Key Link	61
FTB (Fade to Black)	61
Internal color signals	62
Setting the color background	62
Setting the Wash effect	63
Switching the AUX output	64
Selecting the AUX output materials	64
AUX1/2 transitions	64
Setting enable/disable for the AUX1/2 transition	65
Memory	66
Memory registration	67
Memory recall items	67
Storing the settings in the memory (Store)	68
Recalling the operations stored in the memory (Recall)	69
Memory preview	70
Deleting the operations stored in the memory (Delete)	70
Selecting the buses whose settings are to be registered and or played back	71
Setting effect dissolve (shot memory)	72
Editing event memory timelines	73
Macro memory settings	78
Registering memories (Register)	79
Video memories	80
Recording still images (Still)	81
Recording moving images (Clip)	82
Saving Images in Flash Memory	83
Playing back moving images (Clip)	84
Memory card	86
Initializing the memory cards	89
Saving data on memory cards	89
Loading data from memory cards	90
Deleting files on memory cards	91
Displaying the memory card information	92
Waveform monitor settings	93
Input/output signal settings	94
Input signal settings	94
Settings for the exclusionary input connectors	96
Settings for the color range for input signals	96
Checking the input signal status	97
Setting the frame synchronizer	97
Setting the delay amount	98
Freezing the input signals	98
Setting the material names	99
Setting the up-converter	99
Color Corrector	100
Setting the HDMI input signals	103
Displaying the HDMI input signal information	104
Output signal settings	105
Assigning the output signals	106
Setting the SDI output color range	106
Setting the HDMI output signals	107
Setting the down-converter (option)	108
Setting the sync signals	109
Adjusting the output signal phase	109
Setting the multi view display	113
Setting the screen layout	113
Setting the split frame and characters	114
Setting the tally displays	114
Changing the material names	115
Setting the level meters	115
Setting the input signal marks	116
Setting the markers	116
Ancillary settings for the AUX bus, PGM, and PVW	117
System settings	118
Setting the system format	118
Switcher mode settings	118
Dynamic range and color range settings	118
Setting the crosspoints	119
Assigning signals to the crosspoints	119
Setting the crosspoint switching	120
Button assignments	121
Setting the user buttons	121
Setting the date and time	122
Network settings	122
Setting the built-in display backlight and button illumination	123
Status displays	124
Alarm status displays	124
Alarm message	124
Displaying information about the version and optional units	125
Initialization	126
Initializing setting data	126
Initializing fader	126
Remote camera link functions	127
Settings for connections to remote cameras	128
Selecting the terminals for remote camera connection	128
IP address settings	128
Remote camera port settings	129
Remote camera authentication settings	129
Checking the remote camera connection status	129
Remote camera operation direction settings	130
Remote camera tally control settings	130
Selecting the cameras to be operated	131
Controlling in the camera control screen	132
Remote camera settings	133
Selecting the remote camera, checking information, and controlling power	133
Remote camera control speed settings	134
Remote camera on-screen menu and color bar settings	134
Remote camera lens control settings	135
Remote camera image adjustment settings	135
Remote camera preset memory playback settings	136
Disabling remote camera control	136
Controlling in the camera preset memory screen	137
Storing preset memories	139
Recalling preset memories	139
Deleting preset memories	139
Deleting a page of preset memories	140
External interfaces	141
Setting the GPI I/O	141
LAN	144
Controlling with external panels	145
Preparations	145
External panel settings	145
Settings on this unit when external panels are connected	145
List of bus IDs and source IDs	146
Appearance	149
Specifications	150
Setting menu table	152
Appendix (glossary)	181

Match case Limit results 1 per page

Parts and their functions

Rear panel area

TALLY/GPI 1

EXPANTION SLOT A

EXPANTION SLOT B

REF

BOOT

SV NM

SIGNAL

GND

POWER

LAN

12G SDI IN

12G SDI OUT

HDMI IN

HDMI IOUT

AC IN

～

OFF

TALLY/GPI 2































Power switch [POWER]

When the power switch is turned on, the POWER indicator

(

) lights up, and the unit can be operated.



HDMI output connectors [HDMI OUT 1, 2]

Connect to external devices with an HDMI cable.



SDI signal output connectors

[12G SDI OUT 1 to 5]

Assignable with menus



HDMI input connectors [HDMI IN 1, 2]

Connect to external devices with an HDMI cable.



SDI signal input connectors [12G SDI IN 1 to 8]

12G SDI IN 1 to 12G SDI IN 4 can use the up-converter

function.



LAN connector [LAN] (RJ-45) (1000Base-TX)



Refer to “External interfaces”.



Ground connector [SIGNAL GND]

Connect to the system’s earth ground.



AC power input socket [AC IN

]

(AC 100 V to 240 V, 50/60 Hz)

Connect one end of the supplied power cable to this socket

and the other end to the AC outlet.

The supplied power cable comes with a 3-pin power plug.

Be absolutely sure to plug it into a 3-point power outlet as

the power source in order to earth the unit securely.

If a 3-point power outlet is not available for this connection,

be absolutely sure to consult your dealer.



Option slot SLOT A [EXPANSION SLOT A]



Option slot SLOT B [EXPANSION SLOT B]

Each of these is an input/output option slot.

A SDI input unit, HDMI output unit or other optional unit

can be installed in these slots.

For details, refer to “How to install the optional units” and

the operating instructions of the unit concerned.



TALLY/GPI input/output connectors

[TALLY/GPI 1, TALLY/GPI 2]

(D-sub 15-pin, female, inch screw)



Refer to “External interfaces”.



BOOT switch [BOOT SV NM]

This switch is used for maintenance purposes.

For normal operations, select the “NM” (normal) position.



Reference input connector/BB output connector

[REF]

Loop-through output in the external sync mode.

If the loop-through output is not going to be used, provide

a 75-ohm termination.

BB signals output from both connectors in the internal sync

mode.



Cooling fan