Pioneer 141FD Owner's Manual - Page 46

Use Other Equipment With Your Flat Panel, Display

Get Pioneer 141FD - PRO - 59.6inch Elite KURO Plasma Panel PDF manuals and user guides
UPC - 012562905761
View all Pioneer 141FD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

06 Use Other Equipment With Your Flat Panel Display 6 Use Other Equipment With Your Flat Panel Display Although earlier sections have mentioned other equipment for playing back video, this section provides control and operation information for specific types of equipment. 6.1 Program the Remote Control to Operate Other Equipment To operate other equipment or devices through your flat panel display, program the panel's remote control with the equipment's manufacturing code. A manufacturing code is a series of numbers that identify the type of device and the brand. These codes are available in the section entitled "Manufacturer Codes to Program into the Remote Control" in Appendix 9.1 of this manual. 6.1.1 Use the Learning Function The Learning function allows the panel's remote control to memorize codes to control other devices. To set the Learning function to On, follow the directions below. 1 ) Press SELECT to choose the other device. 2 ) Simultaneously press the EDIT/LEARN and 2 buttons to begin. The selected mode indicator flashes when the remote control is ready to be programmed. 3 ) Use the number buttons to learn a manufacturing code. The mode indicator lights up. The Learn session is canceled in 30 seconds and the indicator begins blinking again. When the indicator flashes, the selected device's remote is memorized. When you press a button that cannot be learned, the indicator continues to blink. To exit the Learn mode before it finishes, press EDIT/LEARN. 4 ) Press EDIT/LEARN again to exit the Lean mode after the code is confirmed. 1 2 3 4 5 6 7 8 SUB PIP INPUT SELECT BDP EDIT/LEARN MONITOR STB LD VCR CBL DVD SAT DVR : Notes: The Learn session cancels if: • no operation is performed for more than one minute after having pressed EDIT/LEARN and 2 (the mode indicator is flashing) • you press SELECT 2 cm to 5 cm (0.8 inches to 2.0 inches) Code transmission finishes in approximately two seconds. Do not interrupt the process until the transmission is complete. When using any of the receiver buttons (a, INPUT, or VOL+/-), the learned manufacturer code remains the same. Remote control (Supplied accessory) Remote control of AV product 46 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
46
En
06
Use Other Equipment With Your Flat Panel Display
6
Use Other Equipment With Your Flat Panel
Display
Although earlier sections have mentioned other equipment for playing back video, this section provides control
and operation information for specific types of equipment.
6.1
Program the Remote Control to Operate Other Equipment
To operate other equipment or devices through your flat panel display, program the panel’s remote control with
the equipment’s manufacturing code. A manufacturing code is a series of numbers that identify the type of device
and the brand.
These codes are available in the section entitled “Manufacturer Codes to Program into the Remote
Control” in Appendix 9.1 of this manual.
6.1.1
Use the Learning Function
The Learning function allows the panel’s remote control to memorize codes
to control other devices.
To set the Learning function to On, follow the directions below.
1 ) Press
SELECT
to choose the other device.
2 ) Simultaneously press the
EDIT/LEARN
and
2
buttons to begin.
The selected mode indicator flashes when the remote control is ready
to be programmed.
3 ) Use the number buttons to learn a manufacturing code.
The mode indicator lights up.
The Learn session is canceled in 30 seconds and the indicator begins
blinking again. When the indicator flashes, the selected device’s
remote is memorized.
When you press a button that cannot be learned, the indicator
continues to blink.
To exit the Learn mode before it finishes, press
EDIT/LEARN
.
4 ) Press
EDIT/LEARN
again to exit the Lean mode after the code is confirmed.
:
Notes: The Learn session cancels if:
• no operation is performed for more than one
minute after having pressed
EDIT/LEARN
and
2
(the mode indicator is flashing)
• you press
SELECT
Code transmission finishes in approximately two
seconds. Do not interrupt the process until the
transmission is complete.
When using any of the receiver buttons
(
a
, INPUT
, or
VOL+/–)
, the learned manufacturer
code remains the same.
EDIT/LEARN
VCR
STB
MONITOR
BDP
LD
DVD
DVR
CBL
SAT
SELECT
INPUT
SUB
PIP
1
2
3
4
8
7
6
5
2 cm to 5 cm (0.8 inches to 2.0 inches)
Remote control
(Supplied accessory)
Remote control of
AV product