Sharp MX 4501N Installation Manual - Page 66

Attach the FAX memory., Attach the interface cable., Attach the control PWB and the right rear,

Get Sharp MX 4501N - Color Laser - All-in-One PDF manuals and user guides View all Sharp MX 4501N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

3) Remove the two screws from the control PWB unit. 4) Pull out the control PWB unit. F. Attach the control PWB and the right rear cabinet. 1) Push the control PWB unit into the main unit and secure it with the two screws. D. Attach the FAX memory. 1) Install the FAX memory to the socket on the controller PWB as shown in the figure below so that the memory notch is on the right side. 2) Cut out the cut-out portion of the right rear cabinet. E. Attach the interface cable. 1) Connect the interface cable to the control PWB unit. [Note] Check that the connector is not obliquely inserted. 2) Push the interface cable into the recessed portion of the sheet metal on the control PWB unit. 3) Attach the snap band to the sheet metal of the control PWB unit. 3) Fit the interface cable into the opening that has been cut. 4) Attach the right rear cabinet cover to the main unit. At this time, check that the four hooks are properly fitted to the main unit. 5) Secure the right rear cabinet with the screw. 6) Attach the ozone filter cover to the main unit. MX3500N MX-FXX1 14 - 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
MX3500N
MX-FXX1
14 – 2
3)
Remove the two screws from the control PWB unit.
4)
Pull out the control PWB unit.
D.
Attach the FAX memory.
1)
Install the FAX memory to the socket on the controller PWB as
shown in the figure below so that the memory notch is on the
right side.
E.
Attach the interface cable.
1)
Connect the interface cable to the control PWB unit.
[Note]
Check that the connector is not obliquely inserted.
2)
Push the interface cable into the recessed portion of the sheet
metal on the control PWB unit.
3)
Attach the snap band to the sheet metal of the control PWB
unit.
F.
Attach the control PWB and the right rear
cabinet.
1)
Push the control PWB unit into the main unit and secure it with
the two screws.
2)
Cut out the cut-out portion of the right rear cabinet.
3)
Fit the interface cable into the opening that has been cut.
4)
Attach the right rear cabinet cover to the main unit.
At this time, check that the four hooks are properly fitted to the
main unit.
5)
Secure the right rear cabinet with the screw.
6)
Attach the ozone filter cover to the main unit.